Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

HINT:

Refer to DTC P2120 (see page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P2120).


DTC No. DTC Detection Condition Trouble Area
P2121 Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic):

1. Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V. (learned value of accelerator off position)

2. Difference between VPA and VPA2 is greater than or equal to the specified value.


·

Accelerator pedal sensor assembly

·

ECM



FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to fail-safe mode. In fail-safe mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and then the engine switch is turned off, the fail-safe operation stops and the system returns to normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P2121 is output A
DTC P2121 and other DTCs are output B

HINT:

If any DTCs other than P2121 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT NO.1 AND NO.2)

B

2.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT NO.1 AND NO.2)
A208621E09
2.438,1.76 3.146,1.99 0.708,0.229 10 false Released 0.531,1.771 1.333,2 0.802,0.229 10 false Depressed

a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the values displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V




NG

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

OK

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Operate the accelerator pedal in accordance with the following procedure.

1.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sens. No. 1 Volt %, and Accel Sens. No. 2 Volt %.

2.

Slowly depress the accelerator pedal until Accel Sens. No. 1 Volt % is approximately 30% and Accel Sens. No. 2 Volt % is approximately 46%, then slowly release the accelerator pedal.



i.

Enter the following menus: Powertrain / Engine and ECT / DTC.


j.

Read the DTCs.

Result
Result Proceed to
DTC P2121 is output A
DTC is not output B



A

B

END