Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A079413E73
2.667,0.563 3.417,0.781 0.75,0.219 10 false 4-Pulse 4.719,0.563 5.469,0.781 0.75,0.219 10 false 4-Pulse 1.583,1.135 2.115,1.333 0.531,0.198 10 false ECU 5.771,1.146 6.302,1.344 0.531,0.198 10 false ECM 1.583,0.969 2.583,1.167 1,0.198 10 false Skid Control 0.24,1.177 1.375,1.604 1.135,0.427 10 false From Wheel Speed Sensor 3.375,1.781 5.156,1.979 1.781,0.198 10 false Combination Meter

DTC No. DTC Detection Condition Trouble Area
P0500 While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (1 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM

·

Skid control ECU

·

Vehicle speed sensor



WIRING DIAGRAM

A127263E34
0.543,1.793 1.714,1.957 1.170,0.164 10 Skid Control ECU 2.191,0.81 4.094,1.020 1.904,0.210 10 Combination Meter Assembly 2.191,0.642 2.492,0.852 0.302,0.210 10 G28 2.441,1.682 2.597,1.863 0.156,0.181 10 SI 3.626,1.682 3.816,1.863 0.191,0.181 10 +S 3.92,1.682 4.111,1.863 0.191,0.181 10 40 5.048,1.682 5.148,1.863 0.100,0.181 10 8 5.857,0.838 6.182,1.019 0.326,0.181 10 ECM 5.576,0.838 5.786,1.019 0.210,0.181 10 A7 5.233,1.646 5.535,1.827 0.303,0.181 10 SPD 5.991,1.336 6.295,1.496 0.304,0.160 10 5 V 2.155,1.689 2.345,1.870 0.191,0.181 10 39

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction (see page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

GO TO MALFUNCTION IN SPEEDOMETER

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT/ Data List / Vehicle Speed.


d.

Drive the vehicle.


e.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on GTS and speedometer display are equal.




NG

3.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

OK

3.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
a.
U188517E01
0.077,0.051 1.334,0.261 1.257,0.210 10 Wire Harness Side 1.678,4.251 2.537,4.400 0.859,0.149 10 Turn Wheel 0.057,2.706 0.675,2.855 0.618,0.149 10 5 to 12 V 0.32,4.125 0.578,4.274 0.257,0.149 10 0 V 0.561,1.998 0.814,2.147 0.253,0.149 10 +S 0.838,1.449 0.673,1.952 false 0.871,0.537 2.767,0.747 1.896,0.210 10 Combination Meter Connector 0.392,0.534 0.713,0.697 0.320,0.163 10 G28

Jack up the vehicle.


b.

Shift the transmission gear selector lever to the neutral position.


c.

Turn the engine switch on (IG).


d.

Measure the voltage between the terminal of the combination meter and the body ground while the front wheel is turned slowly.

Standard voltage:
Tester Connection Specified Condition
G28-40 (+S) - Body ground Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for open):
Tester Connection Condition Specified Condition
G28-40 (+S) - A7-8 (SPD) Always Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for short):
Tester Connection Condition Specified Condition
G28-40 (+S) or A7-8 (SPD) - Body ground Always 10 kΩ or higher


HINT:

Because the speed signal is used by other systems, it is possible that a short in the speed signal circuit could cause other systems to malfunction.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR