Home › Engine / Hybrid System › 2AZ-FE FUEL › FUEL TANK
RM24M0E _51 Engine / Hybrid System _059542 2AZ-FE FUEL _0291800 FUEL TANK A

2AZ-FE FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

These procedures should be performed with the fuel tank less than 1/5 full.


PROCEDURE

Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 77310A 3.REMOVE FUEL TANK CAP

Hide 58325E 4.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A126805

Remove the service hole cover and disconnect the fuel pump connector.


Hide 77707 5.DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

Hide 77026A 6.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

Hide 77027 7.DISCONNECT NO. 2 FUEL EVAPORATION TUBE SUB-ASSEMBLY

Hide 77209D 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

Hide 77168A 9.REMOVE FUEL TANK VENT TUBE SET PLATE

Hide 10.DRAIN FUEL

Hide 77020A 11.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 58166A 12.REMOVE FRONT FLOOR COVER LH

a.
A131607

Remove the 4 bolts and floor cover.


Hide 77209D 13.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A131608E01
1.9,2.863 2.509,3.038 0.609,0.175 10 Retainer 2.49,2.608 2.176,2.715 false 2.176,2.715 2.176,2.863 false

Pinch and pull the main tube connector to disconnect the connector from the pipe.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.


·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.


·

Perform this work by hand. Do not use any tools.


·

Do not forcibly bend, twist or turn the nylon tube.


·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




Hide 77026A 14.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Disconnect the purge line hose from the pipe.


Hide 77213B 15.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

A131612

a.

Disconnect the filler pipe hose from the fuel tank.


Hide 77221 16.DISCONNECT NO. 1 FUEL TANK BREATHER TUBE

a.
A131610

Disconnect the breather tube from the fuel tank.

NOTICE:
·

Remove any dirt and foreign matter on the tube joint before performing this work.


·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.


·

Perform this work by hand. Do not use any tools.


·

Do not forcibly bend, twist or turn the nylon tube.


·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




Hide 77707 17.DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A134871

Disconnect the outlet tube from the fuel tank.


Hide 77100 18.REMOVE FUEL TANK ASSEMBLY

a.

Set a mission jack underneath the fuel tank.


b.
A131614

Remove the 6 bolts and 2 fuel tank bands.


c.

Slightly lower the mission jack.