Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL PUMP
RM24M0E _51 Engine / Hybrid System _059543 2GR-FE FUEL _0291805 FUEL PUMP A

2GR-FE FUEL  FUEL PUMP  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 71940A 3.REMOVE REAR SEAT HEADREST ASSEMBLY (for Captain Seat Type)

Hide 4.REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for Captain Seat Type)

Hide 71940A 5.REMOVE REAR SEAT HEADREST ASSEMBLY (for Tumble Seat Type LH Side)

Hide 6.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Tumble Seat Type LH Side)

Hide 58595 7.REMOVE NO. 3 FLOOR CARPET MOULDING

B144646

a.

Using a screwdriver, turn the screw 90° to release the lock and remove the No. 3 floor carpet moulding.

NOTICE:

Do not pry or pull the No. 3 floor carpet moulding because it is easily deformed.


HINT:

Use the same procedure for other the No. 3 floor carpet mouldings.



Hide 72129 8.REMOVE NO. 1 SEAT TRACK LOWER RAIL PROTECTOR

B144538E04
2.615,0.781 2.302,0.26 2.302,0.26 2.094,0.26 false 0.563,0.177 2.104,0.354 1.542,0.177 10 false Roof Moulding Remover

a.

Disengage the claws with a roof moulding remover and remove each seat track lower rail protector.

HINT:

Use the same procedure for the other seat track lower rail protector.



Hide 77310A 9.REMOVE FUEL TANK CAP

Hide 58325E 10.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A126805

Remove the service hole cover and disconnect the fuel pump connector.


Hide 77707 11.DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A126806E02
0.406,0.396 0.323,0.563 false 0.323,0.563 0.323,1.292 false 0.135,1.281 0.688,1.615 0.552,0.333 10 true Retainer

Disconnect the outlet tube from the fuel suction with pump and gauge.


Hide 77026A 12.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Disconnect the tube from the fuel suction with pump and gauge.


Hide 77027 13.DISCONNECT NO. 2 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Disconnect the tube from the fuel suction with pump and gauge.

NOTICE:
·

Remove any dirt and foreign matter on the tube joint before performing this work.


·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.


·

Perform this work by hand. Do not use any tools.


·

Do not forcibly bend, twist or turn the nylon tube.


·

Protect the disconnected parts by covering them with plastic bags and tape after disconnecting the fuel tubes.




Hide 77209D 14.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A126807

Remove the joint clip and fuel tank main tube.

CAUTION:
·

Before removing the tube joint clip, check for foreign matter around the clip. Clean if necessary.


·

Keep the O-ring free of foreign matter, as it becomes contaminated easily.


·

Do not use any tools in this procedure.


·

Do not forcefully bend or twist the tube.


·

Put the tube in a plastic bag to prevent damage and contamination.


·

If the fuel suction plate and tube are stuck together, pinch the tube and turn it carefully to disconnect it.


·

Be careful not to damage the clip. If the clip is damaged, replace it.




Hide 77168A 15.REMOVE FUEL TANK VENT TUBE SET PLATE

a.
A126809

Remove the 8 bolts and set plate.


Hide 77020A 16.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A191109

Disconnect the fuel hose and remove the fuel pump from the fuel tank.

NOTICE:
·

Make sure that the sender gauge arm does not bend.


·

Do not damage the fuel suction with pump and gauge tube assembly.




b.
A191110E07
1.427,0.479 1.104,0.396 false 0.583,0.292 1.073,0.667 0.49,0.375 10 false Gasket

Remove the gasket from the fuel pump.