Home › Engine / Hybrid System › 2AZ-FE COOLING › WATER PUMP › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059552 2AZ-FE COOLING _0291855 WATER PUMP A

2AZ-FE COOLING  WATER PUMP  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Check whether the engine is TMC made or not by referring to the following illustration.

U188506E01
3.93,0.096 4.173,0.285 0.243,0.189 10 *B 0.339,0.096 0.588,0.285 0.249,0.189 10 *A 2.471,0.822 2.640,0.977 0.169,0.154 10 *1 2.471,0.932 2.045,1.143 false 6.069,0.84 6.239,0.994 0.169,0.154 10 *1 6.069,0.964 5.767,1.216 false 4.061,1.835 4.230,1.989 0.169,0.154 10 *2 6.342,1.937 6.511,2.092 0.169,0.154 10 *3 4.233,1.894 4.774,1.749 false 6.33,2.025 5.924,2.109 false

Text in Illustration
*A for TMC Made Engine *B except TMC Made Engine
*1 Engine Oil Level Dipstick Guide *2 Water Inlet Housing
*3 Water Inlet Housing Drain Cock Assembly - -


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 51442 2.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53701 3.REMOVE FRONT FENDER APRON RH

Hide 53292A 4.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 51217A 6.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 16173 9.REMOVE WATER PUMP PULLEY

U188245E02
1.719,0.688 0.438,0.688 false 0.063,0.604 0.396,0.76 0.333,0.156 10 false SST

a.

Using SST, remove the 4 bolts and water pump pulley.

SST
09960-10010  (09962-01000, 09963-00700)


Hide 16100 10.REMOVE WATER PUMP ASSEMBLY (for TMC Made Engine)

a.
A094516

Remove the clamp of the crankshaft position sensor from the water pump.


b.

Disconnect the wire of the crankshaft position sensor from the clamp bracket.


c.
U188544E02
1.958,0.719 2.177,0.406 2.177,0.406 2.594,0.406 true 2.625,0.323 2.844,0.49 0.219,0.167 10 false *1

Remove the 4 bolts, 2 nuts and clamp bracket.

Text in Illustration
*1 Clamp Bracket


d.
A129792

Using a screwdriver, pry between the water pump and cylinder block, and then remove the water pump.

NOTICE:

Be careful not to damage the contact surfaces of the water pump and cylinder block.


HINT:

Tape the screwdriver tip before use.



Hide 16100 11.REMOVE WATER PUMP ASSEMBLY (except TMC Made Engine)

a.
A129794E08
1.729,0.667 0.833,0.521 0.833,0.521 1.833,1.49 true 0.646,0.406 0.802,0.583 0.156,0.177 10 true 1*

Disconnect the connector of the crankshaft position sensor.

Text in Illustration
*1 Clamp Bracket


b.

Disconnect the wire of the crankshaft position sensor from the clamp brackets.


c.
A129795E09
1.625,0.479 2.781,0.646 2.781,0.646 1.927,1.25 false 2.833,0.552 3.031,0.75 0.198,0.198 10 false *1

Remove the 4 bolts, 2 nuts and 2 clamp brackets.

Text in Illustration
*1 Clamp Bracket


d.
A129796

Using a screwdriver, pry between the water pump and cylinder block, and then remove the water pump.

NOTICE:

Be careful not to damage the contact surfaces of the water pump and cylinder block.


HINT:

Tape the screwdriver tip before use.