Home › Drivetrain › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059557 TIRE AND WHEEL _0291871 TIRE PRESSURE WARNING SYSTEM C

TIRE AND WHEEL  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light illuminates and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. DTC Detection Condition Trouble Area
C2198/98 Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C270966E31
5.219,2.969 6.604,3.385 1.385,0.417 10 false Tire Pressure Warning ECU and Receiver 1.948,1.521 4.26,1.802 2.313,0.281 10 false Tire Pressure Warning Reset Switch 1.948,1.333 2.313,1.542 0.365,0.208 10 false G110 2.271,0.906 2.375,1.083 0.104,0.177 10 false 2 3.438,0.906 3.542,1.083 0.104,0.177 10 false 1 5.208,2.792 5.896,3.208 0.688,0.417 10 false M44 5.26,0.885 5.479,1.135 0.219,0.25 10 false 7 5.479,1.01 5.917,1.167 0.438,0.156 10 false CLSW 2.479,0.906 2.604,1.083 0.125,0.177 10 false E 3.104,0.906 3.354,1.063 0.25,0.156 10 false INT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.
C239105E20
0.135,0.096 0.430,0.425 0.295,0.330 10 *a 1.439,1.143 1.685,1.285 0.246,0.142 10 *b 1.843,1.68 2.152,1.822 0.309,0.142 10 *c 2.368,1.64 2.608,1.798 0.240,0.158 10 E 2.914,1.64 3.243,1.798 0.329,0.158 10 INT 2.577,1.245 2.441,1.61 false 2.861,1.245 3.003,1.617 false

Remove the tire pressure warning reset switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (INT) - 2 (E) On Below 1 Ω
Off 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Tire Pressure Warning Reset Switch)
*b On
*c Off


OK

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the G110 tire pressure warning reset switch connector.


b.

Disconnect the M44 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M44-7 (CLSW) - G110-1 (INT) Always Below 1 Ω
M44-7 (CLSW) or G110-1 (INT) - Body ground Always 10 kΩ or higher
G110-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR