Home › Brake › BRAKE › BRAKE FLUID › 2013.04–2014.09
RM24M0E _54 Brake _059558 BRAKE _0291873 BRAKE FLUID N

BRAKE  BRAKE FLUID  BLEEDING  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not operate the brake actuator while air is in the brake system or in the brake master cylinder. Doing so may cause air to enter the brake actuator.

·

If bleeding the brake actuator is difficult due to air in the actuator, replace it with a new one.

·

Wash off brake fluid immediately if it comes in contact with any painted surface.

·

w/ VSC:

If bleeding is performed with the engine running or the engine switch on (IG), DTC C1441 will be stored. Make sure to clear the DTCs when work is complete.



HINT:

If any work is performed on the brake system or if air in the brake lines is suspected, bleed air from the brake system.


PROCEDURE

Hide 1.FILL RESERVOIR WITH BRAKE FLUID

a.

Fill reservoir with brake fluid.

Fluid:

SAE J1703 or FMVSS No. 116 DOT3


NOTICE:

Before replacing the brake fluid or bleeding the brake system, confirm that the reservoir located above the master cylinder assembly is filled with brake fluid.



Hide 2.BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:

If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.


a.

for LHD:



b.
C366247

Using SST, disconnect the 2 brake lines from the master cylinder.

SST
09023-00101  
09023-38201  


c.

Slowly depress and hold down the brake pedal.


d.
C133365

Block the outer holes with your fingers, and release the pedal.


e.

Repeat the 2 previous steps 3 or 4 times.


f.

Using SST, connect the 2 brake lines to the master cylinder.

SST
09023-00101  
09023-38201  

Torque:
w/o VSC : 15 N*m (155 kgf*cm, 11 ft.*lbf)

without SST

14 N*m (144 kgf*cm, 10 ft.*lbf)

with SST


Torque:
w/ VSC : 20 N*m (199 kgf*cm, 14 ft.*lbf)

without SST

18 N*m (185 kgf*cm, 13 ft.*lbf)

with SST


HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

·

This torque value is effective when SST is parallel to a torque wrench.




g.

Hide 3.BLEED AIR FROM BRAKE LINE

NOTICE:

To prevent air from entering the brake lines, bleed the brake lines while keeping the reservoir filled to the MAX line with brake fluid.


C133738E01
0.073,0.025 0.542,0.200 0.469,0.175 10 Front: 3.941,0.025 4.410,0.200 0.469,0.175 10 Rear:

a.

Remove the bleeder plug cap.


b.

Connect a vinyl tube to the bleeder plugs.


c.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.


d.

When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.


e.

Repeat the 2 previous steps until all the air in the brake fluid is gone.


f.

Tighten the bleeder plug.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)

for front brake

10 N*m (102 kgf*cm, 7 ft.*lbf)

for rear brake



g.

Install the cap.


h.

Bleed air from the brake line for each wheel by repeating the above procedures.


Hide 4.CHECK BRAKE FLUID LEVEL IN RESERVOIR

Hide 5.INSPECT FOR BRAKE FLUID LEAK