Home › Brake › BRAKE › REAR BRAKE
RM24M0E _54 Brake _059558 BRAKE _0291879 REAR BRAKE A

BRAKE  REAR BRAKE  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C133389E03
2.462,0.05 3.243,0.227 0.781,0.177 10 Matchmark 1.821,1.035 2.405,0.162 2.405,0.162 1.815,1.179 false

Align the matchmarks and install the disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the adjusting hole plug to the rear disc.


Hide 3.CHECK DISC RUNOUT

Hide 4.ADJUST PARKING BRAKE SHOE CLEARANCE

Hide 47547C 5.TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG

a.

Install the bleeder plug to the brake cylinder.

HINT:

The bleeder plug will be tightened to a torque specification in the "BLEED AIR FROM BRAKE LINE" procedures.



b.

Install the bleeder plug cap to the bleeder plug.


Hide 6.INSTALL PISTON SEAL

a.

Apply lithium soap base glycol grease to a new piston seal.


b.

Install the piston seal to the brake cylinder.

NOTICE:

Securely install the piston seal into the groove of the disc brake cylinder.



Hide 47731 7.INSTALL REAR DISC BRAKE PISTON

a.
C138955E02
0.844,1.031 1.01,0.344 1.01,0.344 1.156,0.344 false 0.885,2.042 0.927,2.427 0.927,2.427 1.031,2.427 false 1.208,0.26 2.156,0.469 0.948,0.208 10 false Cylinder Boot 1.083,2.344 1.552,2.552 0.469,0.208 10 false Piston 0.698,2.906 2.948,3.083 2.25,0.177 10 false Lithium Soap Base Glycol Grease

Apply lithium soap base glycol grease to the brake piston and a new cylinder boot.


b.

Install the cylinder boot to the brake piston.


c.

Install the brake piston (with the cylinder boot) to the brake cylinder.

NOTICE:

Do not forcibly install the brake piston to the brake cylinder.



Hide 8.INSTALL CYLINDER BOOT

a.
C138956E02
0.646,2.073 0.5,2.594 false 0.646,1.448 0.813,0.385 0.813,0.385 0.99,0.385 false 1.031,2.063 1.51,2.74 false 1.042,0.302 1.958,0.49 0.917,0.188 10 false Cylinder Boot 0.188,2.604 0.802,2.792 0.615,0.188 10 false Cylinder 1.51,2.771 1.99,2.948 0.479,0.177 10 false Piston

Install the cylinder boot to the cylinder.

NOTICE:
·

Install the boot securely into the grooves of the brake cylinder and brake piston.

·

Be careful not to damage the boot.




Hide 47775 9.INSTALL REAR DISC BRAKE BUSH DUST BOOT

a.
C138957E02
0.625,2.948 2.833,3.146 2.208,0.198 10 false Lithium Soap Base Glycol Grease

Apply lithium soap base glycol grease to 2 new boots.


b.

Install the 2 boots to the mounting.


Hide 47715D 10.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C138962E02
1.333,0.823 1.073,0.823 1.073,0.823 0.833,1.052 false 0.969,1.99 0.719,1.99 0.719,1.99 0.5,2.208 false 2.167,2.563 2.26,2.177 2.26,2.177 2.396,2.177 false 0.073,1.063 1.188,1.271 1.115,0.208 10 false Slide Pin (Upper) 0.052,2.229 1.167,2.438 1.115,0.208 10 false Slide Pin (Lower) 2.458,2.094 3.208,2.271 0.75,0.177 10 false Slide Bush 0.563,2.917 2.76,3.167 2.198,0.25 10 false Lithium Soap Base Glycol Grease

Apply lithium soap base glycol grease to the pins and a new bush as shown in the illustration.


b.

Install the bush to the pin (lower).


c.
C138950

Install the 2 pins (upper and lower) to the mounting.


Hide 47722A 11.INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

a.
C138949

Install the cylinder mounting with the 2 bolts.

Torque:
88 N*m (900 kgf*cm, 65 ft.*lbf)


Hide 47716 12.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.
C357798

Apply disc brake grease to the areas where the rear disc brake pad support plate contacts the rear disc brake cylinder mounting LH.

Text in Illustration
V100155

Area to Apply Disc Brake Grease


b.

Install the 4 plates to the mounting, following the identification tags or marks.

NOTICE:

Install the 4 plates in the correct positions and direction.



Hide 04466 13.INSTALL REAR DISC BRAKE PAD SUB-ASSEMBLY

a.

Install the 2 disc brake pads to the mounting.

NOTICE:

There should be no oil or grease on the friction surface of the pads and disc.