Home › Steering › POWER STEERING › POWER STEERING SYSTEM › 2014.09–2016.05
RM24M0E _55 Steering _059561 POWER STEERING _0291895 POWER STEERING SYSTEM J

POWER STEERING  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU detects a malfunction, the P/S warning light comes on. At this time, the power steering ECU stores a DTC in its memory.

WIRING DIAGRAM

C367554E01
1.854,0.823 2.25,1.052 0.396,0.229 10 false 32 1.875,1.51 2.271,1.74 0.396,0.229 10 false 31 5.042,0.74 5.438,0.969 0.396,0.229 10 false 1 5.031,1.417 5.427,1.646 0.396,0.229 10 false 7 5.021,3.792 5.417,4.021 0.396,0.229 10 false 6 2.083,3.323 2.479,3.552 0.396,0.229 10 false EPS 0.385,2.333 0.781,2.563 0.396,0.229 10 false G28 0.385,2.5 1.906,2.823 1.521,0.323 10 false Combination Meter 1.292,0.948 1.792,1.198 0.5,0.25 10 false CANH 1.302,1.646 1.74,1.875 0.438,0.229 10 false CANL 5.323,3.115 5.719,3.344 0.396,0.229 10 false PIG 5.323,3.99 5.719,4.219 0.396,0.229 10 false IG 5.313,5.354 5.885,5.573 0.573,0.219 10 false PGND 4.958,0.948 5.354,1.177 0.396,0.229 10 false G91 4.958,3.115 5.354,3.344 0.396,0.229 10 false A21 2.802,1.844 4.458,2.167 1.656,0.323 10 false CAN Communication Line 3.208,4.198 4.365,4.469 1.156,0.271 10 false RH ECU-IG 1.833,4.771 3.052,5.021 1.219,0.25 10 false RH-IG Relay 1 2.021,5.531 2.417,5.76 0.396,0.229 10 false 3 2.271,5.677 2.667,5.906 0.396,0.229 10 false IG1D 2.969,6.021 3.365,6.25 0.396,0.229 10 false AM1 2.271,6.458 2.667,6.688 0.396,0.229 10 false G57 2.281,6.635 3.479,6.906 1.198,0.271 10 false Main Body ECU 2.438,7.823 3.417,8.083 0.979,0.26 10 false AM2 NO. 2 1.396,8.427 2.635,8.656 1.24,0.229 10 false from Battery 5.406,7.979 6.781,8.281 1.375,0.302 10 false Power Steering ECU 5.021,5.177 5.417,5.406 0.396,0.229 10 false 2 4.948,1.625 5.344,1.854 0.396,0.229 10 false G91 5.323,0.958 5.823,1.208 0.5,0.25 10 false CANH 5.333,1.625 5.771,1.854 0.438,0.229 10 false CANL 3.479,5.906 3.875,6.135 0.396,0.229 10 false 6 4.958,5.365 5.354,5.594 0.396,0.229 10 false A21 4.948,3.99 5.344,4.219 0.396,0.229 10 false G91 5.021,2.906 5.417,3.135 0.396,0.229 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

If the steering column or power steering ECU has been replaced, perform the rotation angle sensor initialization and torque sensor zero point calibration (see page Steering>POWER STEERING>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK FOR DTC
a.

Using the intelligent tester, check for DTCs and confirm that there are no problems in the CAN communication system.

OK:

CAN DTCs are not output.




OK

2.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)

NG

2.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Select the item "IG power supply" in the Data List and read the value displayed on the intelligent tester.

Power steering ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG power supply ECU power source voltage:
Min.: 0 V
Max.: 20.1531 V
10 to 14 V Ignition switch on (IG)

OK:

The normal condition value is displayed n the intelligent tester.




NG

3.INSPECT FUSE (RH ECU-IG)

OK

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (P/S INDICATOR)
3.INSPECT FUSE (RH ECU-IG)
a.

Remove the RH ECU-IG fuse from the instrument panel junction block RH.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

4.CHECK WIRE HARNESS (POWER STEERING ECU - BATTERY AND BODY GROUND)

NG

INSPECT SHORT CIRCUIT IN COMPONENTS AND WIRES CONNECTED TO FUSE

4.CHECK WIRE HARNESS (POWER STEERING ECU - BATTERY AND BODY GROUND)
a.
C366251E01
1.917,0.667 2.333,0.917 0.417,0.25 2.417,0.667 2.833,0.917 0.417,0.25 2.021,2.771 2.563,2.354 false 1.75,2.323 2.135,2.219 false 0.146,0.125 1.677,0.365 1.531,0.24 10 false Wire Harness Side: 1.333,2.25 1.896,2.49 0.563,0.24 10 false 6 (IG) 1.385,2.708 2.083,2.958 0.698,0.25 10 false 2 (PGND) 1.979,0.698 2.406,0.969 0.427,0.271 10 false G91 2.5,0.698 3.021,0.927 0.521,0.229 10 false A21

Disconnect the A21 and G91 power steering ECU connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Standard voltage:
Tester Connection Condition Specified Condition
G91-6 (IG) - Body ground Ignition switch on (IG) 10 to 14 V


Standard resistance:
Tester Connection Specified Condition
A21-2 (PGND) - Body ground Below 1 Ω




OK

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (P/S INDICATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (P/S INDICATOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Operate the intelligent tester according to the steps on the display and select the Active test.

Combination meter
Tester Display Test Part Control Range Diagnostic Note
Indicator Light EMPS P/S indicator ON / OFF Confirm that the vehicle is stopped, with the engine idling

OK:

Indicator comes on.




OK

REPLACE POWER STEERING ECU

NG

REPLACE COMBINATION METER