Home › Steering › POWER STEERING › POWER STEERING SYSTEM › from 2014.09
RM24M0E _55 Steering _059561 POWER STEERING _0291895 POWER STEERING SYSTEM C

POWER STEERING  POWER STEERING SYSTEM  C1515  Torque Sensor Zero Point Adjustment Undone  C1525  Rotation Angle Sensor Initialization Undone  


DESCRIPTION

These DTCs do not indicate a malfunction. The power steering ECU outputs these DTCs when it determines that the rotation angle sensor value initialization and torque sensor zero point calibration have not been performed.

DTC No. DTC Detection Condition Trouble Area
C1515 This DTC is detected when torque sensor zero point calibration has not been performed. There is no malfunction if this DTC is not output again after performing zero point calibration
C1525 This DTC is detected when rotation angle sensor value initialization has not been performed. There is no malfunction if this DTC is not output again after performing rotation angle sensor value initialization.

CAUTION / NOTICE / HINT

NOTICE:

If the steering column or power steering ECU has been replaced, perform the rotation angle sensor initialization and torque sensor zero point calibration (see page Steering>POWER STEERING>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT
a.

Initialize the rotation angle sensor value and calibrate the torque sensor zero point (see page Steering>POWER STEERING>POWER STEERING SYSTEM>CALIBRATION).



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Check for DTCs (see page Steering>POWER STEERING>POWER STEERING SYSTEM>DTC CHECK / CLEAR).

Result
Condition Proceed to
DTCs are still output after performing rotation angle sensor value initialization and steering zero point calibration 3 times. A
DTCs are still output even after performing rotation angle sensor value initialization and steering zero point calibration once or twice. B
Normal system code is output. C

HINT:

Replace the power steering ECU if DTCs are still output after performing rotation angle sensor value initialization and steering zero point calibration 3 times.




A

3.REPLACE POWER STEERING ECU

B

1.INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT

C

END

3.REPLACE POWER STEERING ECU
a.

Replace the power steering ECU (for LHD) (see page Steering>POWER STEERING>POWER STEERING ECU(for LHD)>REMOVAL).


b.

Replace the power steering ECU (for RHD) (see page Steering>POWER STEERING>POWER STEERING ECU(for RHD)>REMOVAL).



NEXT

4.INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT
4.INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT
a.

Initialize the rotation angle sensor value and calibrate the torque sensor zero point (see page Steering>POWER STEERING>POWER STEERING SYSTEM>CALIBRATION).



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Check for DTCs (see page Steering>POWER STEERING>POWER STEERING SYSTEM>DTC CHECK / CLEAR).

Result
Condition Proceed to
DTCs are still output after performing rotation angle sensor value initialization and steering zero point calibration 3 times. A
DTCs are still output even after performing rotation angle sensor value initialization and steering zero point calibration once or twice. B
Normal system code is output. C

HINT:

Replace the power steering if DTCs are still output after performing rotation angle sensor value initialization and steering zero point calibration 3 times.


NOTICE:

If replacing the power steering, clear the rotation angle sensor calibration value, initialize the rotation angle sensor value, and calibrate the torque sensor zero point (see page Steering>POWER STEERING>POWER STEERING SYSTEM>CALIBRATION).




A

REPLACE STEERING COLUMN

B

4.INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT

C

END