Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1630/23  Rear Airbag Sensor RH Circuit Malfunction  


DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the center airbag sensor assembly, side airbag sensor RH (for Front Side), side airbag sensor RH (for Rear Side) and rear airbag sensor RH.

The side airbag sensor RH (for Front Side), side airbag sensor RH (for Rear Side) and rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbags should be deployed.

DTC B1630/23 is stored when a malfunction is detected in the rear airbag sensor RH.

DTC No. DTC Detection Condition Trouble Area
B1630/23
·

Rear airbag sensor RH malfunction

·

Center airbag sensor assembly malfunction


·

Rear airbag sensor RH

·

Center airbag sensor assembly



WIRING DIAGRAM

Refer to DTCs B1622/81, B1623/81, B1632/81, B1633/81, B1642/81, B1643/81, B1673/81 and B1674/81 (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>B1622/81).

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK REAR AIRBAG SENSOR RH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the rear airbag sensor RH with LH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the engine switch off.


g.

Turn the engine switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1630/23 is output. A
DTC B1635/24 is output. B
DTCs B1630/23 and B1635/24 are not output. C


HINT:

Codes other than DTCs B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



i.

Turn the engine switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor RH (for Front Side)



A

B

C