The driver side knee airbag squib circuit consists of the center airbag sensor assembly and driver side knee airbag assembly.
The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1860/64 | ·
The center airbag sensor assembly detects a line short in the driver side knee airbag squib circuit during the primary check. ·
Driver side knee airbag squib malfunction ·
Center airbag sensor assembly malfunction |
·
Instrument panel wire ·
Driver side knee airbag assembly (Driver side knee airbag squib) ·
Center airbag sensor assembly |
| B1861/64 | ·
The center airbag sensor assembly detects an open in the driver side knee airbag squib circuit. ·
Driver side knee airbag squib malfunction ·
Center airbag sensor assembly malfunction |
|
| B1862/64 | ·
The center airbag sensor assembly detects a short to ground in the driver side knee airbag squib circuit. ·
Driver side knee airbag squib malfunction ·
Center airbag sensor assembly malfunction |
|
| B1863/64 | ·
The center airbag sensor assembly detects a short to B+ in the driver side knee airbag squib circuit. ·
Driver side knee airbag squib malfunction ·
Center airbag sensor assembly malfunction |
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the driver side knee airbag assembly and center airbag sensor assembly.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the driver side knee airbag assembly and center airbag sensor assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
Check that the instrument panel wire connector (on the driver side knee airbag assembly side) is not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanism of the instrument panel wire connector are not deformed or damaged.
The short springs are not deformed or damaged.
| *1 | Driver Side Knee Airbag Assembly |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
OK
NG
Connect the connector to the center airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the driver side knee airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.
Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector C.
| *1 | Driver Side Knee Airbag Assembly |
| *2 | Center Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Driver Side Knee Airbag Assembly) |
OK
NG
Disconnect the instrument panel wire from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-1 (DK+) - Body ground | Engine switch on (IG) | Below 1 V |
| G14-2 (DK-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-1 (DK+) - G14-2 (DK-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-1 (DK+) - Body ground | Always | 1 MΩ or higher |
| G14-2 (DK-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-1 (DK+) - G14-2 (DK-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Driver Side Knee Airbag Assembly |
| *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Driver Side Knee Airbag Assembly) |
OK
NG
Connect the connectors to the driver side knee airbag assembly and center airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.
Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.
| *1 | Driver Side Knee Airbag Assembly |
| *2 | Center Airbag Sensor Assembly |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG