Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1617/84
B1618/84
·

The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Center airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C238364E98
1.844,0.813 2.146,1.229 0.302,0.417 10 false 2 1.479,0.906 1.958,1.229 0.479,0.323 10 false +SL 1.844,1.979 2.115,2.313 0.271,0.333 10 false 1 1.479,2.073 1.958,2.385 0.479,0.313 10 false -SL 5.146,0.813 5.531,1.094 0.385,0.281 10 false 30 5.375,0.906 5.844,1.26 0.469,0.354 10 false +SL 5.156,1.979 5.427,2.302 0.271,0.323 10 false 28 3.458,0.906 3.865,1.271 0.406,0.365 10 false AG2 3.458,2.083 3.885,2.51 0.427,0.427 10 false AG2 3.542,1.885 3.76,2.188 0.219,0.302 10 false 2 3.542,0.719 3.771,1 0.229,0.281 10 false 1 5.375,2.083 5.813,2.417 0.438,0.333 10 false -SL 0.563,2.896 1.167,3.208 0.604,0.313 10 false A6 0.563,3.083 2.271,3.406 1.708,0.323 10 false Front Airbag Sensor LH 5.344,2.917 5.719,3.198 0.375,0.281 10 false G19 5.344,3.073 6.854,3.469 1.51,0.396 10 false Center Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the center airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)
a.
U189544E02
2.229,0.917 2.052,1.125 false 2.448,0.917 2.656,1.135 false 1.25,3.729 1.042,4.146 false 1.5,3.729 1.698,4.156 false 2.344,1.167 2.344,1.375 false 0.708,2.094 0.813,2.25 0.104,0.156 10 false F 1.021,2.094 1.146,2.25 0.125,0.156 10 false E 1.469,2.094 1.594,2.25 0.125,0.156 10 false D 1.625,2.094 1.75,2.25 0.125,0.156 10 false C 2.073,2.094 2.198,2.25 0.125,0.156 10 false B 2.385,2.094 2.51,2.25 0.125,0.156 10 false A 0.385,2.094 0.573,2.271 0.188,0.177 10 false *1 2.781,2.385 2.938,2.542 0.156,0.156 10 false *2 0.917,0.26 1.115,0.427 0.198,0.167 10 false *a 0.385,3.229 0.552,3.385 0.167,0.156 10 false *b 1.021,0.708 1.302,0.865 0.281,0.156 10 false G19 1.75,1.031 2.01,1.188 0.26,0.156 10 false -SL 2.698,1.031 2.99,1.188 0.292,0.156 10 false +SL 0.573,3.635 0.771,3.792 0.198,0.156 10 false A6 0.854,4.167 1.094,4.323 0.24,0.156 10 false -SL 1.542,4.167 1.823,4.323 0.281,0.156 10 false +SL 2.26,1.385 2.417,1.542 0.156,0.156 10 false *3

Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-2 (+SL) - A6-1 (-SL) Always Below 1 Ω


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

NG

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)
a.
U189539E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.444,2.213 0.635,2.371 0.191,0.158 10 A6 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-2 (+SL) - A6-1 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)
a.
U189539E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.444,2.213 0.635,2.371 0.191,0.158 10 A6 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (+SL) - Body ground Engine switch on (IG) Below 1 V
A6-1 (-SL) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)
a.
U189539E01
0.662,0.599 0.771,0.751 0.109,0.153 10 F 0.971,0.599 1.092,0.751 0.121,0.153 10 E 1.414,0.599 1.535,0.751 0.121,0.153 10 D 1.568,0.599 1.689,0.751 0.121,0.153 10 C 2.023,0.599 2.144,0.751 0.121,0.153 10 B 2.339,0.599 2.460,0.751 0.121,0.153 10 A 0.358,0.599 0.542,0.777 0.184,0.178 10 *1 2.762,0.878 2.930,1.060 0.167,0.181 10 *2 0.166,1.69 0.373,1.853 0.207,0.163 10 *a 0.444,2.213 0.635,2.371 0.191,0.158 10 A6 0.844,2.812 1.104,2.970 0.260,0.158 10 -SL 1.479,2.812 1.800,2.970 0.321,0.158 10 +SL 1.225,2.358 1.036,2.782 false 1.458,2.367 1.654,2.799 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-2 (+SL) - Body ground Always 1 MΩ or higher
A6-1 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)



OK

6.CHECK FRONT AIRBAG SENSOR LH

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR LH
a.
C238211E03
2.195,0.812 2.316,0.967 0.121,0.156 10 A 2.036,0.812 2.157,0.967 0.121,0.156 10 B 1.581,0.812 1.703,0.967 0.121,0.156 10 C 1.425,0.812 1.546,0.967 0.121,0.156 10 D 0.98,0.812 1.101,0.967 0.121,0.156 10 E 0.829,0.812 0.950,0.967 0.121,0.156 10 F 0.514,0.812 0.698,0.989 0.184,0.178 10 *1 2.585,1.092 2.752,1.238 0.167,0.146 10 *2

Connect the connector to the center airbag sensor assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Front Airbag Sensor RH
*2 Center Airbag Sensor Assembly



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U189545E02
2.271,0.927 2.083,1.135 false 2.5,0.927 2.698,1.146 false 1.99,3.729 1.75,4.177 false 2.177,3.74 2.479,4.177 false 1.177,2.26 1.177,2.469 false 1.958,2.26 1.958,2.469 false 2.375,1.167 2.375,1.354 false 0.583,2.094 0.688,2.25 0.104,0.156 10 false F 0.896,2.094 1.021,2.25 0.125,0.156 10 false E 1.344,2.094 1.469,2.25 0.125,0.156 10 false D 1.656,2.094 1.781,2.25 0.125,0.156 10 false C 2.115,2.094 2.24,2.25 0.125,0.156 10 false B 2.427,2.094 2.552,2.25 0.125,0.156 10 false A 1.073,0.625 1.365,0.781 0.292,0.156 10 false G19 1.781,1.052 2.042,1.208 0.26,0.156 10 false -SL 2.729,1.052 3.052,1.208 0.323,0.156 10 false +SL 1.208,3.688 1.5,3.844 0.292,0.156 10 false AG2 2.354,4.208 2.635,4.365 0.281,0.156 10 false +SL 1.604,4.208 1.844,4.365 0.24,0.156 10 false -SL 2.771,2.396 2.969,2.552 0.198,0.156 10 false *2 1.094,2.479 1.292,2.635 0.198,0.156 10 false *3 0.313,2.094 0.51,2.25 0.198,0.156 10 false *1 0.906,0.26 1.104,0.417 0.198,0.156 10 false *a 1.01,3.198 1.208,3.354 0.198,0.156 10 false *b 1.865,2.479 2.063,2.635 0.198,0.156 10 false *4 2.292,1.365 2.448,1.521 0.156,0.156 10 false *5

Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG2-1 (+SL) - AG2-2 (-SL) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U189542E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 0.982,2.156 1.282,2.314 0.300,0.158 10 AG2 1.455,2.681 1.720,2.838 0.265,0.158 10 -SL 2.25,2.681 2.549,2.838 0.299,0.158 10 +SL 1.939,2.242 1.64,2.663 false 2.092,2.238 2.428,2.663 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG2-1 (+SL) - AG2-2 (-SL) Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U189542E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 0.982,2.156 1.282,2.314 0.300,0.158 10 AG2 1.455,2.681 1.720,2.838 0.265,0.158 10 -SL 2.25,2.681 2.549,2.838 0.299,0.158 10 +SL 1.939,2.242 1.64,2.663 false 2.092,2.238 2.428,2.663 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
AG2-1 (+SL) - Body ground Engine switch on (IG) Below 1 V
AG2-2 (-SL) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U189542E01
0.608,0.544 0.718,0.696 0.109,0.153 10 F 0.911,0.544 1.032,0.696 0.121,0.153 10 E 1.364,0.544 1.485,0.696 0.121,0.153 10 D 1.669,0.544 1.789,0.696 0.121,0.153 10 C 2.131,0.544 2.252,0.696 0.121,0.153 10 B 2.442,0.544 2.562,0.696 0.121,0.153 10 A 0.281,0.544 0.456,0.719 0.176,0.175 10 *1 2.813,0.813 2.982,0.987 0.169,0.174 10 *2 1.622,0.068 1.783,0.221 0.160,0.152 10 *4 1.109,0.968 1.304,1.120 0.195,0.152 10 *3 0.734,1.605 0.928,1.789 0.194,0.183 10 *a 0.982,2.156 1.282,2.314 0.300,0.158 10 AG2 1.455,2.681 1.720,2.838 0.265,0.158 10 -SL 2.25,2.681 2.549,2.838 0.299,0.158 10 +SL 1.939,2.242 1.64,2.663 false 2.092,2.238 2.428,2.663 false 1.196,0.695 1.196,0.954 false 1.955,0.554 1.955,0.154 1.955,0.154 1.804,0.154 false

Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG2-1 (+SL) - Body ground Always 1 MΩ or higher
AG2-2 (-SL) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE