Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1666/85  Lost Communication with Center Floor Airbag Sensor  B1667/85  Center Floor Airbag Sensor Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (bus 2) consists of the center airbag sensor assembly and center floor airbag sensor.

The center floor airbag sensor detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbags should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).

DTC No. DTC Detection Condition Trouble Area
B1666/85
B1667/85
·

The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).

·

Center floor airbag sensor malfunction

·

Center airbag sensor assembly malfunction


·

Floor wire

·

No. 2 floor wire

·

Center floor airbag sensor

·

Center airbag sensor assembly



WIRING DIAGRAM

C244889E53
3.427,0.906 3.896,1.5 0.469,0.594 10 false NM1 3.51,0.719 3.865,1.146 0.354,0.427 10 false 2 3.427,2.083 3.854,2.542 0.427,0.458 10 false NM1 3.51,1.896 3.844,2.333 0.333,0.438 10 false 1 5.135,0.813 5.573,1.406 0.438,0.594 10 false 15 5.135,1.99 5.51,2.49 0.375,0.5 10 false 14 5.396,0.896 5.885,1.385 0.49,0.49 10 false BCR+ 5.396,2.073 5.885,2.531 0.49,0.458 10 false BCR- 1.854,0.813 2.25,1.49 0.396,0.677 10 false 2 1.854,1.99 2.188,2.594 0.333,0.604 10 false 1 1.396,0.896 1.927,1.469 0.531,0.573 10 false BER+ 1.396,2.073 1.833,2.563 0.438,0.49 10 false BER- 0.5,2.927 1,3.26 0.5,0.333 10 false M4 0.5,3.083 2.052,3.51 1.552,0.427 10 false Center Floor Airbag Sensor 5.219,2.927 5.604,3.385 0.385,0.458 10 false N9 5.219,3.083 6.844,3.479 1.625,0.396 10 false Center Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the center airbag sensor assembly and center floor airbag sensor. Also check that the connectors that link the floor wire and No. 2 floor wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the center airbag sensor assembly and center floor airbag sensor. Also disconnect the connectors that link the floor wire and No. 2 floor wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (OPEN)
a.
U189770E02
2.125,0.969 2.406,1.271 true 1.948,0.969 1.656,1.271 true 1.365,3.708 1.052,4.135 false 1.635,3.698 1.969,4.135 false 2.052,1.292 2.052,1.406 false 0.667,2.458 0.771,2.615 0.104,0.156 10 false F 0.969,2.458 1.094,2.615 0.125,0.156 10 false E 1.406,2.458 1.531,2.615 0.125,0.156 10 false D 1.563,2.458 1.688,2.615 0.125,0.156 10 false C 2.01,2.458 2.135,2.615 0.125,0.156 10 false B 2.313,2.458 2.438,2.615 0.125,0.156 10 false A 0.333,2.458 0.531,2.646 0.198,0.188 10 false *1 2.729,2.156 2.885,2.344 0.156,0.188 10 false *2 0.625,0.219 0.833,0.417 0.208,0.198 10 false *a 0.375,3.146 0.563,3.333 0.188,0.188 10 false *b 1.208,1.188 1.604,1.396 0.396,0.208 10 false BCR- 2.438,1.188 2.833,1.396 0.396,0.208 10 false BCR+ 0.573,3.583 0.792,3.76 0.219,0.177 10 false M4 1.958,1.417 2.115,1.573 0.156,0.156 10 false *3 0.875,4.146 1.271,4.354 0.396,0.208 10 false BER- 1.802,4.146 2.25,4.354 0.448,0.208 10 false BER+ 1.031,0.604 1.229,0.823 0.198,0.219 10 false N9

Connect the connectors that link the floor wire and No. 2 floor wire.


b.

Using a service wire, connect terminals 15 (BCR+) and 14 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (BER+) - M4-1 (BFR-) Always Below 1 Ω


Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Center Floor Airbag Sensor)



OK

3.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (SHORT)

NG

7.CHECK NO. 2 FLOOR WIRE (OPEN)
3.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (SHORT)
a.
U189766E02
1.125,2.354 0.813,2.771 false 1.396,2.333 1.729,2.76 false 0.667,0.896 0.771,1.052 0.104,0.156 10 false F 0.979,0.896 1.104,1.052 0.125,0.156 10 false E 1.427,0.885 1.552,1.042 0.125,0.156 10 false D 1.573,0.885 1.698,1.042 0.125,0.156 10 false C 2.031,0.885 2.156,1.042 0.125,0.156 10 false B 2.344,0.896 2.469,1.052 0.125,0.156 10 false A 0.313,0.792 0.51,0.979 0.198,0.188 10 false *1 2.75,0.5 2.906,0.688 0.156,0.188 10 false *2 0.198,1.729 0.385,1.917 0.188,0.188 10 false *a 0.385,2.208 0.656,2.365 0.271,0.156 10 false M4 0.604,2.792 1,2.969 0.396,0.177 10 false BER- 1.625,2.792 2.146,3.021 0.521,0.229 10 false BER+

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (BER+) - M4-1 (BFR-) Always 1 MΩ or higher


Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Center Floor Airbag Sensor)



OK

4.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (SHORT TO B+)

NG

8.CHECK NO. 2 FLOOR WIRE (SHORT)
4.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (SHORT TO B+)
a.
U189766E02
1.125,2.354 0.813,2.771 false 1.396,2.333 1.729,2.76 false 0.667,0.896 0.771,1.052 0.104,0.156 10 false F 0.979,0.896 1.104,1.052 0.125,0.156 10 false E 1.427,0.885 1.552,1.042 0.125,0.156 10 false D 1.573,0.885 1.698,1.042 0.125,0.156 10 false C 2.031,0.885 2.156,1.042 0.125,0.156 10 false B 2.344,0.896 2.469,1.052 0.125,0.156 10 false A 0.313,0.792 0.51,0.979 0.198,0.188 10 false *1 2.75,0.5 2.906,0.688 0.156,0.188 10 false *2 0.198,1.729 0.385,1.917 0.188,0.188 10 false *a 0.385,2.208 0.656,2.365 0.271,0.156 10 false M4 0.604,2.792 1,2.969 0.396,0.177 10 false BER- 1.625,2.792 2.146,3.021 0.521,0.229 10 false BER+

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M4-2 (BER+) - Body ground Engine switch on (IG) Below 1 V
M4-1 (BFR-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Center Floor Airbag Sensor)



OK

5.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (SHORT TO GROUND)

NG

9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
5.CHECK SIDE COLLISION SENSOR RH CIRCUIT (BUS 2) (SHORT TO GROUND)
a.
U189766E02
1.125,2.354 0.813,2.771 false 1.396,2.333 1.729,2.76 false 0.667,0.896 0.771,1.052 0.104,0.156 10 false F 0.979,0.896 1.104,1.052 0.125,0.156 10 false E 1.427,0.885 1.552,1.042 0.125,0.156 10 false D 1.573,0.885 1.698,1.042 0.125,0.156 10 false C 2.031,0.885 2.156,1.042 0.125,0.156 10 false B 2.344,0.896 2.469,1.052 0.125,0.156 10 false A 0.313,0.792 0.51,0.979 0.198,0.188 10 false *1 2.75,0.5 2.906,0.688 0.156,0.188 10 false *2 0.198,1.729 0.385,1.917 0.188,0.188 10 false *a 0.385,2.208 0.656,2.365 0.271,0.156 10 false M4 0.604,2.792 1,2.969 0.396,0.177 10 false BER- 1.625,2.792 2.146,3.021 0.521,0.229 10 false BER+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (BER+) - Body ground Always 1 MΩ or higher
M4-1 (BFR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Center Floor Airbag Sensor)



OK

6.CHECK CENTER FLOOR AIRBAG SENSOR

NG

10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
6.CHECK CENTER FLOOR AIRBAG SENSOR
a.
C358414E02
2.198,1.198 2.552,1.396 0.354,0.198 10 false A 2.615,0.927 2.969,1.125 0.354,0.198 10 false *2 2.042,1.198 2.396,1.396 0.354,0.198 10 false B 1.594,1.198 1.948,1.396 0.354,0.198 10 false C 1.438,1.198 1.792,1.396 0.354,0.198 10 false D 0.979,1.198 1.333,1.396 0.354,0.198 10 false E 0.833,1.198 1.188,1.396 0.354,0.198 10 false F 0.5,1.188 0.854,1.385 0.354,0.198 10 false *1

Connect the connector to the center airbag sensor assembly.


b.

Interchange the center floor airbag sensor with rear floor airbag sensor and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1666/85, B1667/85, B1678/86 and B1679/86 are not output. A
DTC B1678/86 or B1679/86 is output. B
DTC B1666/85 or B1667/85 is output. C


HINT:

Codes other than DTCs B1666/85, B1667/85, B1678/86 and B1679/86 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the center floor airbag sensor and rear floor airbag sensor to their original positions and connect the connectors.

Text in Illustration
*1 Rear Floor Airbag Sensor
*2 Center Airbag Sensor Assembly



A

B

C

7.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U189771E02
2.125,0.969 2.385,1.26 true 1.927,0.99 1.656,1.281 true 2.031,1.302 2.031,1.417 false 1.385,3.688 1.083,4.104 false 1.615,3.708 1.948,4.135 false 1.156,2.458 1.156,1.969 1.156,1.969 1.01,1.969 false 1.875,2.458 1.875,1.969 1.875,1.969 1.729,1.969 false 0.625,2.469 0.729,2.625 0.104,0.156 10 false F 0.896,2.458 1.021,2.615 0.125,0.156 10 false E 1.323,2.469 1.448,2.625 0.125,0.156 10 false D 1.604,2.469 1.729,2.625 0.125,0.156 10 false C 2.042,2.49 2.167,2.646 0.125,0.156 10 false B 2.313,2.479 2.438,2.635 0.125,0.156 10 false A 0.813,1.885 1,2.042 0.188,0.156 10 false *3 1.229,1.156 1.646,1.323 0.417,0.167 10 false BCR- 2.448,1.177 2.875,1.375 0.427,0.198 10 false BCR+ 0.958,0.646 1.385,0.938 0.427,0.292 10 false N9 0.594,3.615 0.896,3.771 0.302,0.156 10 false M4 0.302,2.469 0.51,2.625 0.208,0.156 10 false *1 2.708,2.167 2.917,2.323 0.208,0.156 10 false *2 0.625,0.229 0.833,0.385 0.208,0.156 10 false *a 0.375,3.115 0.583,3.271 0.208,0.156 10 false *b 1.531,1.896 1.719,2.052 0.188,0.156 10 false *4 0.875,4.125 1.26,4.333 0.385,0.208 10 false BER- 1.844,4.167 2.26,4.375 0.417,0.208 10 false BER+ 1.948,1.448 2.104,1.604 0.156,0.156 10 false *5

Disconnect the No. 2 floor wire connector from the floor wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (BER+) - M4-1 (BER-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*4 No. 2 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE NO. 2 FLOOR WIRE

8.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
U189767E02
1.938,2.333 1.646,2.76 false 2.198,2.333 2.531,2.76 false 1.167,0.917 1.167,0.396 1.167,0.396 1,0.396 false 1.885,0.906 1.885,0.385 1.885,0.385 1.729,0.385 false 0.594,0.885 0.698,1.042 0.104,0.156 10 false F 0.875,0.885 1,1.042 0.125,0.156 10 false E 1.323,0.885 1.448,1.042 0.125,0.156 10 false D 1.604,0.875 1.729,1.031 0.125,0.156 10 false C 2.063,0.875 2.188,1.031 0.125,0.156 10 false B 2.344,0.896 2.469,1.052 0.125,0.156 10 false A 0.802,0.302 0.99,0.458 0.188,0.156 10 false *3 1.167,2.198 1.469,2.354 0.302,0.156 10 false M4 0.271,0.833 0.479,0.99 0.208,0.156 10 false *1 2.76,0.531 2.969,0.688 0.208,0.156 10 false *2 1.01,1.708 1.25,1.917 0.24,0.208 10 false *a 1.521,0.313 1.708,0.469 0.188,0.156 10 false *4 1.448,2.771 1.875,2.958 0.427,0.188 10 false BER- 2.385,2.781 2.813,2.979 0.427,0.198 10 false BER+

Disconnect the No. 2 floor wire connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (BER+) - M4-1 (BER-) Always 1 MΩ or higher


Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE NO. 2 FLOOR WIRE

9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U189767E02
1.938,2.333 1.646,2.76 false 2.198,2.333 2.531,2.76 false 1.167,0.917 1.167,0.396 1.167,0.396 1,0.396 false 1.885,0.906 1.885,0.385 1.885,0.385 1.729,0.385 false 0.594,0.885 0.698,1.042 0.104,0.156 10 false F 0.875,0.885 1,1.042 0.125,0.156 10 false E 1.323,0.885 1.448,1.042 0.125,0.156 10 false D 1.604,0.875 1.729,1.031 0.125,0.156 10 false C 2.063,0.875 2.188,1.031 0.125,0.156 10 false B 2.344,0.896 2.469,1.052 0.125,0.156 10 false A 0.802,0.302 0.99,0.458 0.188,0.156 10 false *3 1.167,2.198 1.469,2.354 0.302,0.156 10 false M4 0.271,0.833 0.479,0.99 0.208,0.156 10 false *1 2.76,0.531 2.969,0.688 0.208,0.156 10 false *2 1.01,1.708 1.25,1.917 0.24,0.208 10 false *a 1.521,0.313 1.708,0.469 0.188,0.156 10 false *4 1.448,2.771 1.875,2.958 0.427,0.188 10 false BER- 2.385,2.781 2.813,2.979 0.427,0.198 10 false BER+

Disconnect the No. 2 floor wire connector from the floor wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M4-2 (BER+) - Body ground Engine switch on (IG) Below 1 V
M4-1 (BER-) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE NO. 2 FLOOR WIRE

10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U189767E02
1.938,2.333 1.646,2.76 false 2.198,2.333 2.531,2.76 false 1.167,0.917 1.167,0.396 1.167,0.396 1,0.396 false 1.885,0.906 1.885,0.385 1.885,0.385 1.729,0.385 false 0.594,0.885 0.698,1.042 0.104,0.156 10 false F 0.875,0.885 1,1.042 0.125,0.156 10 false E 1.323,0.885 1.448,1.042 0.125,0.156 10 false D 1.604,0.875 1.729,1.031 0.125,0.156 10 false C 2.063,0.875 2.188,1.031 0.125,0.156 10 false B 2.344,0.896 2.469,1.052 0.125,0.156 10 false A 0.802,0.302 0.99,0.458 0.188,0.156 10 false *3 1.167,2.198 1.469,2.354 0.302,0.156 10 false M4 0.271,0.833 0.479,0.99 0.208,0.156 10 false *1 2.76,0.531 2.969,0.688 0.208,0.156 10 false *2 1.01,1.708 1.25,1.917 0.24,0.208 10 false *a 1.521,0.313 1.708,0.469 0.188,0.156 10 false *4 1.448,2.771 1.875,2.958 0.427,0.188 10 false BER- 2.385,2.781 2.813,2.979 0.427,0.198 10 false BER+

Disconnect the No. 2 floor wire connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-2 (BER+) - Body ground Always 1 MΩ or higher
M4-1 (BER-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE NO. 2 FLOOR WIRE