Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291902 FRONT PASSENGER AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a front passenger airbag with an unactivated airbag.

·

The airbag produces a loud, exploding sound when it activates. Perform the operation where it will not be a nuisance to people nearby.

·
C110371E62
0.958,1.219 0.74,0.771 false 0.573,0.583 0.885,0.781 0.313,0.198 10 false SST

When activating the airbag, always use the specified SST (SRS airbag deployment tool).

·

Perform procedures in a place away from electrical interference.

·

When activating the airbag, stand at least 10 m (33 ft.) away from the airbag.

·

The airbag becomes very hot when it is deployed. Do not touch it for at least 30 minutes after activation.

·

Use gloves and safety glasses when handling a deployed airbag.

·

Do not apply water to a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the front passenger side knee airbag, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPARTMENT of the DISTRIBUTOR.


Hide 73970A 2.DISPOSE OF FRONT PASSENGER AIRBAG ASSEMBLY TOGETHER WITH VEHICLE

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E62
0.958,1.219 0.74,0.771 false 0.573,0.583 0.885,0.781 0.313,0.198 10 false SST

Check if SST is functioning properly.

SST
09082-00700  

i.

Connect the SST's red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.

HINT:

The yellow connector will be used to connect to another SST in a later step.



ii.
C110475E28
1.76,0.625 1.458,0.313 false 1.188,0.167 1.542,0.365 0.354,0.198 10 false SST

Press the SST activation switch, and check that the LED of the SST activation switch illuminates.

CAUTION:

If the LED illuminates when the activation switch is not pressed, SST may have a malfunction, in which case that SST should not be used.



iii.

Disconnect SST from the battery.




c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



d.

Remove the glove compartment door (see page Vehicle Interior>INTERIOR PANEL>UPPER INSTRUMENT PANEL>REMOVAL).


e.

Install SST.

i.
C136830

Disconnect the front passenger airbag connector.

NOTICE:

When handling the airbag connector, do not damage the airbag wire harness.



ii.
C136831E01
1.11,1.793 1.332,1.939 0.222,0.145 10 (A) 1.772,1.093 1.994,1.238 0.222,0.145 10 (B)

Connect SST (A) to SST (B). Then connect SST (B)'s connector to the cable.

SST
09082-00700  
09082-00780  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.



iii.
U186046E02
1.01,1.875 2.49,1.875 false 2.625,1.063 2.625,1.938 false 0.865,1.823 0.865,1.948 false 0.469,1.219 0.688,1.521 false 1.792,0.479 2.271,0.688 0.479,0.208 10 false Battery 0.146,1.125 0.5,1.333 0.354,0.208 10 false SST 1.219,1.438 2.146,1.646 0.927,0.208 10 false 10 m or more

Move SST at least 10 m (33 ft.) away from the front side window.


iv.

Maintaining enough clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



v.

Connect the SST's red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.



f.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
·

When deploying the airbag, make sure that no one is near the vehicle.

·

The airbag becomes extremely hot when it is deployed. Do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a deployed airbag.

·

Do not apply water to a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the SST activation switch LED illuminates.




Hide 73970A 3.DISPOSE OF ONLY FRONT PASSENGER AIRBAG ASSEMBLY

NOTICE:
·

When disposing of the airbag, never use the customer's vehicle to deploy the airbag.

·

Be sure to follow the procedure detailed below when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E62
0.958,1.219 0.74,0.771 false 0.573,0.583 0.885,0.781 0.313,0.198 10 false SST

Check if SST is functioning properly.

SST
09082-00700  

i.

Connect the SST's red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.

HINT:

The yellow connector will be used to connect to another SST in a later step.



ii.
C110475E28
1.76,0.625 1.458,0.313 false 1.188,0.167 1.542,0.365 0.354,0.198 10 false SST

Press the SST activation switch, and check that the LED of the SST activation switch illuminates.

CAUTION:

If the LED illuminates when the activation switch is not pressed, SST may have a malfunction, in which case that SST should not be used.



iii.

Disconnect SST from the battery.



b.

Remove the front passenger airbag (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

When removing the airbag, work must be started 90 seconds after the ignition switch is turned off and after the cable is disconnected from the negative (-) battery terminal.

·

When storing the airbag, keep the airbag deployment side facing upward.




c.
B104882E04
1.857,1.189 1.857,1.567 false 1.245,0.261 2.741,0.465 1.496,0.204 10 Wire Harness Diameter 0.652,1.586 2.620,1.788 1.968,0.202 10 Stripped Wire Harness Section

Using service wire harnesses for the vehicle, tie down the airbag to a tire.

Wire harness:

Stripped wire harness section

1.25 mm2 or more (0.0019 in.2 or more)


NOTICE:

Use a tire that you are planning to throw away, as the airbag deployment may damage the tire.


CAUTION:

Do not use wire harnesses that are too thin or any other substitute items to tie down the front passenger airbag. They may snap when the airbag deploys. Always use vehicle wire harnesses that have an area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire harness section:

Area = 3.14 x Diameter2/4


i.

Position the airbag inside the tire so that the brackets contact the tire.

Tire size minimum:

Width minimum: 185 mm (7.28 in.)

Inner diameter minimum: 360 mm (14.17 in.)



ii.

Wind 3 wire harnesses at least twice around the airbag brackets and tire.

H103116E01
0.531,3.521 1.302,3.719 0.771,0.198 10 false Width 3.521,2.5 4.094,2.958 0.573,0.458 10 false Inner Diameter

CAUTION:
·

Tightly wind the wire harnesses around the brackets so that there is no slack.

·

Make sure that the wire harnesses are tight. If there is slack in a wire harness, the airbag may come loose when it is deployed.

·

Always tie down the airbag with the airbag deployment side facing inside the tire.





d.

Install SST.

i.

Connect the SST connector to the airbag.



e.
H044501E11
2.365,0.375 3.229,0.542 0.865,0.167 8 true Tires (2 or more) 2.365,1.552 3.25,1.74 0.885,0.188 8 true Tires (2 or more)

Place the tires.

i.

Place at least 2 tires under the tire to which the airbag is tied.


ii.

Place at least 2 tires on top of the tire to which the airbag is tied. The top tire should have a disc wheel installed.

NOTICE:
·

Do not place the SST connector under the tire as the connector may be damaged.

·

Use a disc wheel that you are planning to throw away, as the airbag deployment will damage the disc wheel.

·

Use tires that you are planning to throw away, as the airbag deployment may damage the tires.




iii.
H042763

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. If there is slack in a wire harness, the tires may come loose when the airbag is deployed.




f.

Install SST.

i.
H044502E18
1.563,0.281 2.344,1.042 false 0.625,0.052 2.115,0.26 1.49,0.208 10 false Front Passenger Airbag 0.198,1.25 0.594,1.448 0.396,0.198 10 false SST 1.365,0.969 1.958,1.177 0.594,0.208 10 false Battery 1.083,1.854 2.115,2.052 1.031,0.198 10 false 10 m or more

Connect the SST connector.

SST
09082-00700  
09082-00802  (09082-10801, 09082-30801)

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.




g.

Deploy the airbag.

i.

Connect the SST's red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (33 ft.) radius of the airbag.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

When deploying the airbag, make sure that no one is near the tires.


HINT:

The airbag is deployed as the SST activation switch LED illuminates.




h.
H041436

Dispose of the airbag.

CAUTION:
·

The airbag becomes extremely hot when it is deployed. Do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a deployed airbag.

·

Do not apply water to a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the airbag from the tire.


ii.

Place the airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.