1. TABLE OF BOLT, SCREW AND NUT
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
55404C
3.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Remove the 3 clips.
Disengage the 5 claws and 3 guides, and remove the instrument cluster finish panel.
55420A
4.REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER ASSEMBLY (for LHD)
Apply protective tape on the positions shown in the illustration.
| *1 | Protective Tape |
Using a molding remover, disengage the 13 claws.
Remove the instrument cluster finish panel center and then disconnect the connectors.
55414A
5.REMOVE INSTRUMENT CLUSTER FINISH PANEL END (for LHD)
w/o Navigation System:
Disengage the 6 claws, and remove the instrument cluster finish panel end.
33504F
6.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for RHD)
for U241E: (See page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER(for RHD)>REMOVAL)
for U660E: (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER(for RHD)>REMOVAL)
for K112: (See page Drivetrain>K112 (CVT)>SHIFT LEVER(for RHD)>REMOVAL)
7.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for RHD)
Apply protective tape on the positions shown in the illustration.
|
Protective Tape |
Move the shift lever to N.
Using a molding remover, disengage the 12 claws and 5 clips.
Remove the center instrument cluster finish panel assembly and then disconnect the connectors.
55414A
8.REMOVE INSTRUMENT CLUSTER FINISH PANEL END (for RHD)
Remove the 2 screws.
Disengage the 2 claws to remove the instrument cluster finish panel end.
55522B
9.REMOVE RADIO TUNER OPENING COVER (w/o Radio Receiver)
Remove the 4 screws and opening cover.
10.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
11.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)
45186
12.REMOVE NO. 2 STEERING WHEEL LOWER COVER (for LHD)
45187
13.REMOVE NO. 3 STEERING WHEEL LOWER COVER (for LHD)
45130
14.REMOVE STEERING PAD ASSEMBLY (for LHD)
45187
15.REMOVE LOWER NO. 3 STEERING WHEEL COVER (for RHD)
45186
16.REMOVE LOWER NO. 2 STEERING WHEEL COVER (for RHD)
45130
17.REMOVE STEERING PAD ASSEMBLY (for RHD)
45100
18.REMOVE STEERING WHEEL ASSEMBLY (for LHD)
45286
19.REMOVE STEERING COLUMN COVER (for LHD)
20.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE (for LHD)
45100
21.REMOVE STEERING WHEEL ASSEMBLY (for RHD)
45286
22.REMOVE STEERING COLUMN COVER (for RHD)
23.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE (for RHD)
55650
24.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)
Apply protective tape on the positions shown in the illustration.
| *1 | Protective Tape |
Using a molding remover, disengage the 4 claws, and remove the register.
55041B
25.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY (for LHD)
Disengage the 10 claws and remove the box door.
55041B
26.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY (for RHD)
Apply protective tape on the positions shown in the illustration.
|
Protective Tape | - | - |
Disengage the 13 claws as shown in the illustration.
Disconnect the connector to remove the No. 1 instrument panel box door sub-assembly.
55660
27.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)
Apply protective tape on the positions shown in the illustration.
| *1 | Protective Tape |
Using a molding remover, disengage the 4 claws and remove the register.
55042B
28.REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY (for LHD)
Disengage the 6 claws and remove the box door.
55042B
29.REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY (for RHD)
Apply protective tape on the positions shown in the illustration.
|
Protective Tape |
Disengage the 10 claws to remove the No. 2 instrument panel box door sub-assembly.
62226
30.REMOVE FRONT PILLAR GARNISH LOWER LH
62212
31.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
62212
32.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
62225A
33.REMOVE FRONT PILLAR GARNISH LOWER RH
62211
34.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
62211
35.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
55550
36.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
Open the glove compartment door.
Disengage the claw from the glove compartment door stopper.
Insert a finger into part A and bend the part in the direction indicated by the arrow in the illustration to disengage the stopper.
Insert a finger into part B and bend the part in the direction indicated by the arrow in the illustration to disengage the stopper. Lower the glove compartment door assembly until the front of the door is level.
Pull the glove compartment door assembly horizontally toward the rear of the vehicle to disengage the 2 hinges. Remove the glove compartment door assembly.
Pulling the compartment door upward to remove it causes the hinges to be deformed when reinstalling the door. Be sure to pull out the compartment door horizontally to remove it.
37.DISCONNECT FRONT PASSENGER AIRBAG CONNECTOR
55302A
38.REMOVE UPPER INSTRUMENT PANEL
Remove the 2 bolts, and remove the passenger airbag.
Disconnect the connectors and clamps.
Disengage the 9 claws and 5 guides, and remove the upper instrument panel.