Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD(for RHD) › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291912 STEERING PAD(for RHD) N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD(for RHD)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a steering pad assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the steering pad assembly.

·

The steering pad assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad assembly with a deployed airbag.

·

Do not apply water, etc. to a steering pad assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the steering pad assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 45130 2.DISPOSE OF STEERING PAD ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the steering pad assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E64
0.969,1.219 0.74,0.729 0.74,0.729 0.521,0.729 false 0.24,0.656 0.615,0.854 0.375,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS airbag deployment tool


i.
C110372E34
0.5,0.719 0.833,0.719 0.833,0.719 0.833,1.646 false 2.708,0.771 2.51,0.771 false 0.208,0.635 0.521,0.833 0.313,0.198 10 false SST 2.74,0.677 2.948,0.875 0.208,0.198 10 false *a

Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

Text in Illustration
*a Battery


ii.
C110475E29
1.771,0.635 1.458,0.313 false 1.198,0.167 1.552,0.365 0.354,0.198 10 false SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.




c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



d.

Remove the steering column cover (lower) (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for RHD)>REMOVAL).


e.

Disconnect the yellow airbag connector from the spiral cable with steering angle sensor.

i.
B279733E03
0.927,2.333 1.219,2.042 1.219,2.042 1.448,2.042 true 1.479,1.958 1.708,2.156 0.229,0.198 10 false *a

Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with steering angle sensor.

Text in Illustration
*a Slider

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




f.

Install SST.

CAUTION:

Check that there is no looseness in the steering wheel assembly and steering pad assembly.


i.
B450329E02
1.667,1.615 2.24,1.615 2.24,1.615 2.24,1.094 true 1.906,1.104 1.906,1.615 true 1.271,1.521 1.604,1.708 0.333,0.188 10 false SST

After connecting the following SST to each other, connect them to the spiral cable with steering angle sensor.

SST
09082-00700  
09082-00780  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
U110943E03
1.01,1.854 2.49,1.854 false 2.625,1.042 2.625,1.917 false 0.875,1.792 0.875,1.917 false 0.385,1.229 0.594,1.229 false 0.594,1.229 0.594,1.573 false 1.719,0.813 1.948,0.177 false 1.948,0.177 2.167,0.177 false 2.198,0.073 2.375,0.25 0.177,0.177 10 false *a 0.021,1.115 0.406,1.313 0.385,0.198 10 false SST 1.615,1.885 1.844,2.083 0.229,0.198 10 false *b

Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

Text in Illustration
*a Battery
*b 10 m (32.8 ft.) or more


iii.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



g.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch to deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The steering pad assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad assembly with a deployed airbag.

·

Do not apply water, etc. to a steering pad assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 45130 3.DISPOSE OF STEERING PAD ASSEMBLY (When not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E64
0.969,1.219 0.74,0.729 0.74,0.729 0.521,0.729 false 0.24,0.656 0.615,0.854 0.375,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS airbag deployment tool


i.
C110372E34
0.5,0.719 0.833,0.719 0.833,0.719 0.833,1.646 false 2.708,0.771 2.51,0.771 false 0.208,0.635 0.521,0.833 0.313,0.198 10 false SST 2.74,0.677 2.948,0.875 0.208,0.198 10 false *a

Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

Text in Illustration
*a Battery


ii.
C110475E29
1.771,0.635 1.458,0.313 false 1.198,0.167 1.552,0.365 0.354,0.198 10 false SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.



b.

Remove the steering pad assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD(for RHD)>REMOVAL).

CAUTION:
·

Before removing the steering pad assembly, wait at least 90 seconds after turning the engine switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the steering pad assembly, keep the airbag deployment side facing upward.




c.
B448601E05
2.083,0.948 2.344,0.365 2.344,0.365 2.115,0.365 false 1.813,0.281 2.125,0.479 0.313,0.198 10 false *b 2.677,1.51 2.99,1.708 0.313,0.198 10 false *a

Using braided wire, tie down the steering pad assembly to an unneeded tire and wheel set.

Text in Illustration
*a Wire Diameter
*b Stripped Wire Cross Sectional Area

Wire:

Stripped wire cross sectional area

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the steering pad assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the cross sectional area of the stripped wire:

Cross sectional area = 3.14 x (Diameter)2 / 4


i.
B381104E01
2.443,1.342 2.773,1.522 0.330,0.180 10 SST 1.792,2.056 1.792,1.428 1.792,1.428 2.406,1.428 false 2.18,1.997 2.18,1.428 false

After connecting the following SST to each other, connect them to the steering pad assembly.

SST
09082-00802  (09082-10801, 09082-40800)


ii.
B381105E03
2.302,3.615 2.125,3.813 2.125,3.813 1.958,3.813 true 1.156,3.646 1.156,4.094 true 1.042,0.75 1.042,0.156 1.042,0.156 2.646,0.156 true 2.25,0.74 2.25,0.156 true 1.708,1.646 2.323,1.646 false 1.083,4.125 1.24,4.313 0.156,0.188 10 false *a 1.771,3.729 1.927,3.917 0.156,0.188 10 false *a 2.354,1.552 2.51,1.74 0.156,0.188 10 false *a 2.729,0.073 2.885,0.26 0.156,0.188 10 false *a

Wind 3 wires at least 2 times each around each of the pins.

Text in Illustration
*a 2 times or more

CAUTION:
·

Tightly wind the wires around the pins without any slack.

·

Make sure that the wires are tight. If there is slack in the wires, the steering pad assembly may break loose when the airbag is deployed.




iii.
B381106E03
0.042,0.979 0.229,1.177 0.188,0.198 10 false *a 1.76,1.885 1.948,2.083 0.188,0.198 10 false *b

Face the airbag deployment side of the steering pad assembly upward on top of an unneeded tire and wheel set. Separately tie each side of the steering pad assembly to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

Text in Illustration
*a Width
*b Inner Diameter

Minimum Tire Size:
Width:

185 mm (7.28 in.)

Inner Diameter:

360 mm (14.17 in.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the steering pad assembly may break loose when the airbag is deployed.

·

Always tie down the steering pad assembly with the airbag deployment side facing upward.



NOTICE:

The wheel and tire may be damaged by the airbag deployment, so use an unneeded tire and wheel set.




d.
B381107E01
2.484,0.251 2.810,0.440 0.326,0.189 10 SST 3.238,0.616 2.973,0.351 2.973,0.351 2.867,0.351 false

Install SST.

CAUTION:

Place the tire and wheel set on level ground.


i.

Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the wheel.



ii.
B369944E03
0.958,1.51 1.292,1.51 false 1.302,1.438 1.625,1.604 0.323,0.167 10 false SST 1.375,1.74 1.563,1.917 0.188,0.177 10 false *a

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the wheel.

Text in Illustration
*a 10 m (32.8 ft.) or more



e.

Cover the steering pad assembly (using a cardboard box).

i.
B369945E02
0.99,1.542 0.604,1.542 true 2.802,1.615 2.417,1.615 true 1.219,0.156 1.365,0.302 0.146,0.146 10 false Y 1.042,0.729 1.188,0.875 0.146,0.146 10 false Y 2.771,0.885 2.917,1.031 0.146,0.146 10 false X 0.396,1.448 0.583,1.625 0.188,0.177 10 false *a 2.802,1.521 2.99,1.698 0.188,0.177 10 false *a

Cover the steering pad assembly with a cardboard box.

Text in Illustration
*a Weight


ii.

Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

Minimum Cardboard Box Size:

Must exceed the following dimensions

X:

460 mm (1.51 ft.)

Y:

650 mm (2.13 ft.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the diameter of the wheel and tire to which the steering pad assembly is tied, X should be the following size.

X = 460 mm (1.51 ft.) + width of tire

·

If a cardboard box smaller than the specified size is used, it may be broken by the shock of the airbag deployment.





f.

Cover the steering pad assembly (using tires).

i.
B369941E01
0.641,1.682 0.829,1.889 0.188,0.207 10 *a 1.609,0.296 1.797,0.503 0.188,0.207 10 *b 2.549,0.84 2.737,1.047 0.188,0.207 10 *c

Place at least 3 tires without wheels onto the tire and wheel set to which the steering pad assembly is tied.

Text in Illustration
*a Tires (3 or more)
*b Inner Diameter
*c Width


ii.

Place a tire and wheel set on top.

Minimum Tire Size:
Width:

185 mm (7.28 in.)

Inner Diameter:

360 mm (14.17 in.)


CAUTION:

Do not use tires with wheels except for on the top and bottom.


NOTICE:
·

The wheels and tires may be damaged by the airbag deployment, so use unneeded wheels and tires.

·

Do not place the SST connector under the tire because it could be damaged.




iii.
C223306

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.




g.

Deploy the airbag.

i.
B369942E04
0.469,1.188 0.75,1.188 false 1.396,1.354 1.583,1.354 false 2.583,1.458 2.76,1.635 2.76,1.635 2.76,2.042 true 0.469,3.198 0.75,3.198 false 1.396,3.365 1.583,3.365 false 2.688,3.521 2.865,3.698 2.865,3.698 2.865,4.104 true 0.146,2.333 0.365,2.51 0.219,0.177 10 false *b 0.146,0.104 0.365,0.281 0.219,0.177 10 false *a 0.094,1.104 0.417,1.292 0.323,0.188 10 false SST 1.583,1.25 1.771,1.438 0.188,0.188 10 false *c 1.302,2.042 1.49,2.229 0.188,0.188 10 false *d 2.667,2.042 2.854,2.229 0.188,0.188 10 false *1 0.094,3.115 0.417,3.302 0.323,0.188 10 false SST 1.583,3.26 1.771,3.448 0.188,0.188 10 false *c 1.385,4.052 1.573,4.24 0.188,0.188 10 false *d 2.771,4.104 2.958,4.292 0.188,0.188 10 false *1

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

Text in Illustration
*1 Steering Pad Assembly
*a Using a Cardboard Box
*b Using Tires
*c Battery
*d 10 m (32.8 ft.) or more


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the steering pad assembly is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the steering pad assembly.

CAUTION:
·

The steering pad assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad assembly with a deployed airbag.

·

Do not apply water, etc. to a steering pad assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the steering pad assembly from the tire and wheel set.


ii.

Place the steering pad assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.