Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for RHD) › from 2016.05
RM24M0E _55 Steering _059560 STEERING COLUMN _0291893 STEERING COLUMN ASSEMBLY(for RHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

a.

Disconnect each connector from the spiral cable.


b.
C353562E01
1.888,0.536 0.534,0.536 false 1.888,0.777 0.745,0.777 0.745,0.777 0.745,0.536 false 0.302,0.433 0.507,0.613 0.205,0.180 10 *a

Remove the nut and place matchmarks on the steering wheel assembly and steering column assembly.

Text in Illustration
*a Matchmark


c.
C353563E02
2.26,1.021 2.958,1.021 true 2.344,2.333 2.927,2.333 true 2.615,3.021 2.823,3.188 0.208,0.167 10 false *a 0.625,2.146 0.833,2.313 0.208,0.167 10 false *b 3.01,0.927 3.333,1.104 0.323,0.177 10 false SST 2.979,2.24 3.344,2.458 0.365,0.219 10 true SST

Using SST, remove the steering wheel assembly.

Text in Illustration
*a Turn
*b Hold

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05070)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 45286 4.REMOVE STEERING COLUMN COVER

NOTICE:

Removing the steering column cover in the incorrect order will cause the steering column cover to break.


a.

Release the tilt lever.


b.
C353564

Push the right and left sides of the steering column cover (lower side), and disengage the 2 claws.


c.
C353565

Insert fingers into the opening of the tilt lever of the steering column cover (lower side) to disengage the claw.

HINT:

Spread the claw to disengage it.



d.
C353566E01
0.226,0.823 0.427,0.987 0.201,0.164 10 *a 0.93,3.618 1.120,3.781 0.191,0.163 10 *b 1.041,0.909 0.457,0.909 false 3.032,3.437 3.032,3.715 3.032,3.715 1.144,3.715 false 2.17,3.437 2.17,3.715 false

Using a screwdriver, insert the tip into each service hole to disengage the 2 claws and remove the steering column cover (lower side).

Text in Illustration
*a Protective Tape
*b Service Hole

HINT:

Tape the screwdriver tip before use.



e.
C353568

Disengage the 3 claws, 4 clips, and 2 pins, and remove the steering column cover (upper side).


Hide 5.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE

a.

Disconnect each connector from the turn signal switch assembly with spiral cable.


b.
C353569E02
2.781,0.625 2.781,0.229 2.781,0.229 1.375,0.229 true 2.552,0.552 1.802,0.552 true 1.635,0.458 1.823,0.646 0.188,0.188 10 false *a 1.208,0.146 1.396,0.333 0.188,0.188 10 false *b

Using pliers, expand the clamp.

Text in Illustration
*a Clamp
*b Claw


c.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable from the steering column assembly.


Hide 33504F 6.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 7.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 55041B 8.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55446A 9.REMOVE NO. 1 SWITCH HOLE BASE

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>REMOVAL).


Hide 67913B 10.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
·

Perform the same procedure as for the LH side (See page Vehicle Interior>INTERIOR>ROOF HEADLINING>REMOVAL).

·

This is symmetrical to the LHD model



Hide 62111C 11.REMOVE COWL SIDE TRIM BOARD RH

HINT:
·

Perform the same procedure as for the LH side (See page Vehicle Interior>INTERIOR>ROOF HEADLINING>REMOVAL).

·

This is symmetrical to the LHD model



Hide 55606 12.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>REMOVAL).


Hide 55432B 13.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/o Driver Side Knee Airbag)

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>REMOVAL).


Hide 55432B 14.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/ Driver Side Knee Airbag)

HINT:

This is symmetrical to the LHD model (See page Vehicle Interior>INTERIOR PANEL>LOWER INSTRUMENT PANEL>REMOVAL).


Hide 73900 15.REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 87201F 16.REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

a.
C356268

Remove the clip.


b.

Disengage the 2 claws to remove the No. 3 air duct sub-assembly.


Hide 45259A 17.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C136577

Turn back the floor carpet.


b.

Remove the 2 clips and column hole cover silencer sheet.


Hide 45260 18.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C136578E06
1.854,1.375 2.698,1.375 false 1.813,1.448 2.49,1.448 2.49,1.448 2.49,1.375 false 2.708,1.281 2.875,1.448 0.167,0.167 10 false *a

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.

Separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft assembly.


Hide 19.REMOVE STEERING COLUMN ASSEMBLY

a.
C356278

Disconnect the 2 connectors from the power steering ECU assembly.


b.

Disconnect each connector and disengage each wire harness clamp from the steering column assembly.


c.
C353570

Remove the bolt, 2 nuts and steering column assembly.

NOTICE:

Do not drop or strike the steering column assembly. If dropped or struck, replace it with a new one.



Hide 45260 20.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C136583E02
3.013,0.402 3.185,0.551 0.172,0.149 10 *a 1.446,1.047 1.446,0.489 1.446,0.489 3,0.489 false 1.507,1.095 1.507,0.489 false

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.