Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  Headlight Signal Circuit  


DESCRIPTION

The headlight leveling ECU assembly detects the status of the low beam headlights.

WIRING DIAGRAM

E349361E03
5.885,2.229 6.5,2.427 0.615,0.198 10 false HRLY 5.26,0.698 5.875,0.896 0.615,0.198 10 false HDLP 2,1.885 3.49,2.083 1.49,0.198 10 false to H-LP RL Fuse 1.99,2.51 3.479,2.708 1.49,0.198 10 false to H-LP LL Fuse 2.948,1.604 3.563,1.802 0.615,0.198 10 false H-LP 0.167,0.688 1.021,1.104 0.854,0.417 10 false from Battery 5.333,3.198 5.667,3.385 0.333,0.188 10 false 4L 4.917,1.031 5.25,1.219 0.333,0.188 10 false A39 4.948,1.188 7.125,1.406 2.177,0.219 10 false Headlight Leveling ECU Assembly 5.573,3.208 6.719,3.521 1.146,0.313 10 false Main Body ECU 3.531,1.115 3.688,1.313 0.156,0.198 10 false 3 3.521,0.573 3.677,0.771 0.156,0.198 10 false 1 2.542,0.552 2.698,0.75 0.156,0.198 10 false 2 2.552,1.115 2.708,1.313 0.156,0.198 10 false 5 5.01,0.583 5.167,0.781 0.156,0.198 10 false 3 5.094,2.104 5.25,2.302 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

First check that the low beam headlights operate normally.

·

If the headlight leveling ECU assembly has been replaced, initialization of the headlight leveling ECU assembly is necessary (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(for LED Headlight)>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the GTS.

HL AutoLeveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Headlight Low Beam State Low beam headlight state/ON or OFF ON: Low beam headlights on
OFF: Low beam headlights off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT LEVELING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the A39 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP relay terminal) - A39-3 (HDLP) Always Below 1 Ω
1 (H-LP relay terminal) or A39-3 (HDLP) Always 10 kΩ or higher




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR