Home › Vehicle Interior › WIPER / WASHER › FRONT WIPER MOTOR
RM24M0E _58 Vehicle Interior _059565 WIPER / WASHER _0291976 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
B145937E02
0.479,1.917 0.917,2.094 0.438,0.177 10 false Clamp

Install the wiper motor with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Attach the clamp.


Hide 2.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY

a.
E168933

Temporarily install the front wiper crank sub-assembly on the windshield wiper motor assembly with the nut.


b.

When reusing the front wiper crank sub-assembly:

i.
E168934

Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.



c.
E168935

Temporarily install the windshield wiper motor and link on the crank arm pivot of the front wiper crank sub-assembly.


d.

Align the front wiper crank sub-assembly with the windshield wiper motor and link as shown in the illustration.

E168936E01
3.032,0.119 4.241,0.528 1.210,0.409 10 Front Wiper Crank Sub-Assembly 4.967,0.708 4.654,0.179 4.654,0.179 4.3,0.179 false 0.584,0.719 1.712,1.099 1.128,0.381 10 Windshield Wiper Link Assembly 3.062,1.463 2.395,0.796 2.395,0.796 1.705,0.796 false


e.

Tighten install the front wiper crank subassembly with the nut.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


f.
E168935

Connect the rod of the windshield wiper link assembly to the crank arm pivot of the front wiper crank sub-assembly.


Hide 85160 3.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

B460067E01
0.448,1.906 1.021,2.135 0.573,0.229 10 true : Clmp

a.

Install the wiper motor and link to the front cowl top outside panel with the 4 bolts.


b.

Attach the clamp.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
B145938

Apply grease to the lip circumference of the front wiper grommet.

HINT:

Apply grease to the inner circumference of the lip without blocking the hole.



d.

Install the front wiper grommet to the front cowl top outside.


Hide 55712 4.INSTALL FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

B145933

a.

Install the cowl top outside panel with the 10 bolts.

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


b.
B145932

Connect the connector.


Hide 47233 5.INSTALL BRAKE MASTER CYLINDER RESERVOIR BRACKET

B145931

a.

Install the brake master cylinder reservoir bracket with the 2 bolts.

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


Hide 55781F 6.INSTALL COWL TOP VENTILATOR LOUVER

B460066

a.

Attach the 6 claws to install the louver.


b.
B145123

Install the 2 clips.


c.
B145939

Install the washer hose.


Hide 53866J 7.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

B145941E01
2.182,2.551 2.344,2.721 0.163,0.170 10 A 0.532,2.578 0.673,2.741 0.141,0.163 10 B

a.

When reusing the front fender to cowl side seal:

i.

Attach the clip labeled A to install the front fender to cowl side seal.



b.

When installing a new front fender to cowl side seal:

i.

Attach the clip labeled A and claw labeled B to install the front fender to cowl side seal.



Hide 53867H 8.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

B145940E01
1.161,2.564 1.297,2.724 0.136,0.161 10 A 2.893,2.571 3.012,2.718 0.119,0.147 10 B

a.

When reusing the front fender to cowl side seal:

i.

Attach the clip labeled A to install the front fender to cowl side seal.



b.

When installing a new front fender to cowl side seal:

i.

Attach the clip labeled A and claw labeled B to install the front fender to cowl side seal.



Hide 85211B 9.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E358371E01
1.542,1.479 1.167,0.813 false 1.344,3.021 1.281,2.76 1.281,2.76 1.052,2.76 false 1.885,3.271 2.094,2.781 2.094,2.781 2.292,2.781 false 0.417,0.729 1.115,1.146 0.698,0.417 10 false Wiper Arm Serration 0.292,2.667 1.104,3 0.813,0.333 10 false Wire Brush 2.354,2.708 3.094,3.115 0.74,0.406 10 false Wiper Pivot Serration

a.

Stop the wiper motor at the automatic stop position.


b.

Clean the wiper arm serration with a round file or equivalent.


c.

Clean the wiper pivot serration with a wire brush.


d.
B145942

Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the arm hinge with your hand while tightening the nut.



e.

Operate the front wipers while spraying water or washer fluid on the windshield. Ensure that there is no interference between the blades and pillar.


Hide 85221B 10.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E358371E01
1.542,1.479 1.167,0.813 false 1.344,3.021 1.281,2.76 1.281,2.76 1.052,2.76 false 1.885,3.271 2.094,2.781 2.094,2.781 2.292,2.781 false 0.417,0.729 1.115,1.146 0.698,0.417 10 false Wiper Arm Serration 0.292,2.667 1.104,3 0.813,0.333 10 false Wire Brush 2.354,2.708 3.094,3.115 0.74,0.406 10 false Wiper Pivot Serration

a.

Stop the wiper motor at the automatic stop position.


b.

Clean the wiper arm serration with a round file or equivalent.


c.

Clean the wiper pivot serration with a wire brush.


d.
B145943

Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the arm hinge with your hand while tightening the nut.



e.

Operate the front wipers while spraying water or washer fluid on the windshield. Ensure that there is no interference between the blades and pillar.


Hide 85192 11.INSTALL FRONT WIPER ARM HEAD CAP

B145120

a.

Install the 2 caps.


Hide 53867H 12.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 13.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 75534 14.INSTALL WINDSHIELD MOULDING OUTSIDE LH

Hide 75533 15.INSTALL WINDSHIELD MOULDING OUTSIDE RH

HINT:

Use the same procedure as for the LH side.


Hide 16.INSTALL CABLE TO NEGATIVE BATTERY TERMINAL

Hide 17.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.