The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock / unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights), wireless door lock buzzer signal to the wireless door lock buzzer.
Check the wireless door lock control system function (see page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Each function of wireless door lock control system operates normally using transmitter switches.
NG
OK
Check that the transmitter's LED illuminates 3 times when the is switch pressed 3 times.
Transmitter's LED illuminates 3 times when switch is pressed 3 times.
NG
OK
Temporarily replace the transmitter battery with a new or normally functioning one (see page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REMOVAL).
Check that the doors can be locked and unlocked using the transmitter switches.
Doors can be locked and unlocked with transmitter.
NG
OK
Check that the room No. 1 light illumination operates normally.
Inspect the wireless door lock buzzer (see page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>No Answer-Back).
| Result | Proceed to |
|---|---|
| Room No. 1 light and wireless door lock buzzer is normal | A |
| Room No. 1 light is malfunctioning | B |
| Wireless door lock buzzer is malfunctioning | C |
A
B
C
Switch to self-diagnostic mode.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch ON.
Refer to the intelligent tester operator's manual for further details.
Check that the system has switched to self-diagnostic mode by checking the room No. 1 light flash and wireless door lock buzzer sound patterns.
Room No. 1 light flash and wireless door lock buzzer sound patterns are same as illustration.
OK
NG
Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the room No. 1 light flash and wireless door lock buzzer sound patterns.
| Result | Proceed to |
|---|---|
| No diagnosis outputs | A |
| Normal waves (light flash or buzzer sound patterns) for LOCK and UNLOCK switches are output | B |
| Unmatching recognition code is output | C |
A
B
C
Temporarily replace the door control transmitter with a new or normally functioning one.
Press and hold down the door control transmitter's switch.
Check that an unmatching recognition code is output.
Unmatching recognition code is output.
NG
OK
Measure the voltage of the connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N26-5 (DATA) - Body ground | Ignition switch off, all doors closed and transmitter switch not pressed → pressed | Below 1 V → 6 to 7 V → Below 1 V |
OK
NG
Disconnect the G29 ECU connector.
Disconnect the N26 receiver connector.
Measure the resistance or the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G29-29 (RCO) - N26-4 (+5) | Below 1 Ω |
| G29-38 (RDA) - N26-5 (DATA) | Below 1 Ω |
| G29-39 (RSSI) - N26-2 (RSSI) | Below 1 Ω |
| G29-29 (RCO) - Body ground | 10 kΩ or higher |
| G29-38 (RDA) - Body ground | 10 kΩ or higher |
| G29-39 (RSSI) - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the G59 and G29 ECU connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G59-15 (CANN) - G29-28 (CANL) | Below 1 Ω |
| G59-16 (CANP) - G29-27 (CANH) | Below 1 Ω |
| G59-15 (CANN) - Body ground | 10 kΩ or higher |
| G59-16 (CANP) - Body ground | 10 kΩ or higher |
OK
NG
Temporarily replace the door control receiver with a new or normally functioning one.
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
Doors can be locked and unlocked with transmitter.
NG
OK
Temporarily replace the ECU aggregation box (certification ECU) with a new or normally functioning one.
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
Doors can be locked and unlocked with transmitter.
OK
NG