Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2014.09–2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

C146747E14
3.708,1.75 4,1.292 4,1.292 4.063,1.292 false 4.135,1.198 4.979,1.417 0.844,0.219 10 Acceptable 4.292,3.01 5.188,3.229 0.896,0.219 10 Temperature 1.531,0.625 2.313,0.844 0.781,0.219 10 Resistance

The CVT fluid temperature sensor converts the fluid temperature into a resistance value which is detected by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in heavy traffic.


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0712
1.

-

2.

There is a short circuit in the CVT fluid temperature sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Short in CVT fluid temperature sensor circuit

·

Continuously variable transaxle assembly

·

ECM


P0713
1.

15 minutes or more after starting the engine.

2.

There is an open circuit in the CVT fluid temperature sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Open in CVT fluid temperature sensor circuit

·

Continuously variable transaxle assembly

·

ECM



MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and detects open or short circuits in the CVT fluid temperature sensor circuit. If the resistance value of the CVT fluid temperature sensor is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the CVT fluid temperature sensor or wiring. The ECM turns on the MIL and stores the DTC.

*1: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.

*2: -40°C (-40°F) is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked on the intelligent tester display.


WIRING DIAGRAM

C200615E24
5.813,2.938 6.125,3.135 0.313,0.198 10 false D2 5.813,3.125 6.198,3.323 0.385,0.198 10 false ECM 5.625,1.24 6.042,1.438 0.417,0.198 10 false THO1 5.333,2.333 5.563,2.531 0.229,0.198 10 false 95 5.333,1.375 5.531,1.573 0.198,0.198 10 false 72 5.625,2.208 6.115,2.406 0.49,0.198 10 false ETHO 3.229,1.125 3.594,1.323 0.365,0.198 10 false THO 3.625,2.323 3.854,2.521 0.229,0.198 10 false 6 3.615,1.365 3.813,1.563 0.198,0.198 10 false 1 3.302,2.073 3.521,2.271 0.219,0.198 10 false E2 1.469,1.729 3.427,1.927 1.958,0.198 10 false CVT Fluid Temperature Sensor 1.167,2.677 1.479,2.875 0.313,0.198 10 false D67 1.167,2.865 3.302,3.229 2.135,0.365 10 false Transmission Wire (Continuously Variable Transaxle Assembly)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (A/T OIL TEMPERATURE 1)
a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 CVT fluid temperature sensor value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
·

After stall speed test: Approx. 80°C (176°F)

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.

Result
Result Proceed to
Data displayed is not as specified under Normal Condition A
Data displayed is as specified under Normal Condition B



A

2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)

B

6.REPLACE ECM
2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
a.
C199169E73
2.115,0.948 2.469,0.479 true 2.469,1.698 2.115,1.229 true 2.5,0.365 2.917,0.563 0.417,0.198 10 false THO 0.073,0.063 0.385,0.26 0.313,0.198 10 false *1 2.521,1.635 2.813,1.833 0.292,0.198 10 false E2

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THO) - 6 (E2) Always 79 Ω to 156 kΩ
1 (THO) - Body ground Always 10 kΩ or higher
6 (E2) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is outside the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may be affected.


Resistance (Reference):
CVT Fluid Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



Text in Illustration
*1 Component without harness connected
(Transmission Wire)


OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

8.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D2-72 (THO1) - D2-95 (ETHO) Always 79 Ω to 156 kΩ
D2-72 (THO1) - Body ground Always 10 kΩ or higher
D2-95 (ETHO) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.PERFORM INITIALIZATION
6.REPLACE ECM

NEXT

7.PERFORM INITIALIZATION
8.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NEXT

9.PERFORM INITIALIZATION