Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM U

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


Stop Light Switch Stop light switch status/
ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
SPD (NT) Input turbine speed/
min.: 0 rpm
max.: 12750 rpm
·

Lock-up on (After warming up engine): Input turbine speed (NT) equal to engine speed

·

Lock-up off (Idling with shift lever in P or N): Input turbine speed (NT) nearly equal to engine speed

·

Vehicle stopped with shift lever in R: 0 rpm


Data is displayed in increments of 50 rpm.
Shift SW Status (P Range) PNP switch status/
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


Shift SW Status (R Range) PNP switch status/
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


Shift SW Status (N Range) PNP switch status/
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
·

ON: Shift lever in D

·

OFF: Shift lever not in D


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


A/T Oil Temperature 1 CVT fluid temperature sensor value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
·

After stall speed test: Approx. 80°C (176°F)

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.
SPD (NIN) Primary pulley speed (NIN)/
min.: 0 rpm
max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed


Data is displayed in increments of 50 rpm.
SPD (NOUT) Secondary pulley speed (NOUT)/
min.: 0 rpm
max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Vehicle cruising at approx. 60 km/h (37 mph): 2650 rpm


Data is displayed in increments of 50 rpm.
A/T Oil Pressure Secondary oil pressure value/
min.: -0.625 MPa
max.: 9.575 MPa
Secondary oil pressure inspection
·

D position stall speed test: 4.0 to 5.0 MPa

·

R position stall speed test: 3.6 to 4.2 MPa


-
G sensor Converted output voltage of G sensor/
min.: 0 V
max.: 5 V
Displays converted voltage of G sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-
Solenoid (DSU) Shift solenoid valve DSU status/
ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Lock Up Lock-up/
ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Lock Up Solenoid Status Shift solenoid valve SL status/
ON or OFF
·

ON: Shift solenoid valve SL on

·

OFF: Shift solenoid valve SL off


-
Shift Status*1 ECM gearshift command/
1st, 2nd, 3rd, 4th or 5th
Same as actual gear -
Solenoid (DS2) Shift solenoid valve DS2 status/
ON or OFF
·

OFF: Constant cruising with shift lever in D

·

ON: Accelerator pedal depressed further after cruising with shift lever in D


-
Solenoid (DS1) Shift solenoid valve DS1 status/
ON or OFF
·

ON: Driving with shift lever in D and accelerator pedal depressed

·

OFF: Accelerator pedal released when driving with shift lever in D with accelerator pedal depressed


-
Solenoid (SLS) Shift solenoid valve SLS status/
ON or OFF
·

ON: After engine start

·

OFF: Engine switch on (IG)


-
G Sensor Calibration G sensor calibration status/
Incomplete or Complete
Complete -
AT Fluid Lock-up judder judgment/
ON or OFF
·

ON: Judder judgment occurs

·

OFF: Judder judgment does not occur


-
G Sensor Learning Value G sensor learned value voltage/
min.: 0 V
max.: 5 V
G sensor calibration is complete: 2.31 V to 2.69 V -
CVT Oil Press Calibration CVT oil pressure calibration status/
Incomplete or Complete
Complete -

*1:"Shift Status" is a signal divides into 5 gear position for ACTIVE TEST.

It does not express gear ratio for normal driving and gear positions for 7-speed sport sequential shiftmatic mode.



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.

Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Connect the TC and TE1 Turn on and off TC and TE1 connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


Activate the Lock Up Operate lock-up ON or OFF Possible to check lock-up operation.
HINT:

Perform "Activate the Lock Up" while monitoring the engine speed (ESPD) and turbine speed (NT).


[Vehicle Condition]
Vehicle speed: 40 km/h (25 mph) or more
Activate the Solenoid (SL) Operate shift solenoid valve SL ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Control the Shift Position Operates the shift solenoid valves to allow the gear ratio to be manually selected [1st - 2nd - 3rd - 4th - 5th]
Reference gear ratios:
1st (2.4 gear ratio max.) - 2nd (1.5) - 3rd (1.0) - 4th (0.7) - 5th (0.43 gear ratio min.)
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Used to check the operation of the shift solenoid valves.
NOTICE:

Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.


[Vehicle Condition]
50 km/h (30 mph) or less
HINT:

Perform "Control the Shift Position" while monitoring "Shift Status" to confirm actual gear position.


Activate the Solenoid (DSU) Operate shift solenoid valve DSU ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (DS1) Operate shift solenoid valve DS1 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (DS2) Operate shift solenoid valve DS2 ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Control the SLS Pressure Operate shift solenoid valve SLS High or Low [Vehicle Condition]
·

Vehicle stopped

·

Engine idling


Activate the Solenoid (SLS) Operate shift solenoid valve SLS ON or OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N