Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch and shift lock control unit assembly (transmission control switch) detect the shift lever position and send signals to the ECM.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0705
1.

Engine switch on (IG) and battery voltage is 10.5 V or more

2.

Any 2 or more of the following signals are ON simultaneously.

-

(NSW, P, N) input signal

-

R input signal

-

D input signal


3.

2 seconds

4.

2-trip detection logic


·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch

·

Shift lock control unit assembly

(Transmission control switch)

·

ECM


1.

Engine switch on (IG) and battery voltage is 10.5 V or more

2.

All switches are OFF simultaneously

-

NSW input signal

-

P input signal

-

R input signal

-

N input signal

-

D input signal


3.

60 seconds

4.

2-trip detection logic


1.

Engine switch on (IG) and battery voltage is 10.5 V or more

2.

When any of following conditions is met and the M signal is ON

-

NSW input signal is ON

-

P input signal is ON

-

R input signal is ON

-

N input signal is ON


3.

2 seconds

4.

2-trip detection logic



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM. For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or M).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C211628E05
5.823,6.594 6.167,6.74 0.344,0.146 10 false ECM 4.292,1.927 5.125,2.125 0.833,0.198 10 false to ST Relay 0.479,1.948 1.833,2.313 1.354,0.365 10 false from Main Body ECU (STAR) 5.823,6.427 6.135,6.625 0.313,0.198 10 false D2 5.604,5.76 5.917,5.958 0.313,0.198 10 false S 5.323,5.896 5.542,6.094 0.219,0.198 10 false 74 5.604,4.177 5.917,4.375 0.313,0.198 10 false P 5.323,4.302 5.542,4.5 0.219,0.198 10 false 73 5.604,3.573 5.917,3.771 0.313,0.198 10 false R 5.323,3.698 5.542,3.896 0.219,0.198 10 false 53 5.604,2.99 5.917,3.188 0.313,0.198 10 false N 5.323,3.094 5.542,3.292 0.219,0.198 10 false 54 5.604,2.375 5.917,2.573 0.313,0.198 10 false D 5.323,2.5 5.542,2.698 0.219,0.198 10 false 56 5.583,1.354 6.052,1.552 0.469,0.198 10 false (NSW) 5.323,1.323 5.542,1.521 0.219,0.198 10 false 52 3.771,2.052 3.99,2.25 0.219,0.198 10 false 9 3.771,2.51 3.99,2.708 0.219,0.198 10 false 7 3.771,3.094 3.99,3.292 0.219,0.198 10 false 8 3.771,4.292 3.99,4.49 0.219,0.198 10 false 3 3.771,3.698 3.99,3.896 0.219,0.198 10 false 2 3.75,5.896 3.969,6.094 0.219,0.198 10 false 13 3.583,1.813 3.802,2.01 0.219,0.198 10 false L 3.49,2.26 3.76,2.458 0.271,0.198 10 false DL 3.5,2.854 3.771,3.052 0.271,0.198 10 false NL 2.771,3.135 3.042,3.333 0.271,0.198 10 false RB 3.5,3.438 3.771,3.635 0.271,0.198 10 false RL 3.49,4.063 3.76,4.26 0.271,0.198 10 false PL 3.583,5.646 3.854,5.844 0.271,0.198 10 false S 2.781,1.823 3,2.021 0.219,0.198 10 false B 2.771,5.635 3.042,5.833 0.271,0.198 10 false IG 2.583,2.063 2.802,2.26 0.219,0.198 10 false 4 2.625,3.396 2.844,3.594 0.219,0.198 10 false 1 2.573,5.885 2.844,6.083 0.271,0.198 10 false 6 2.292,6.26 2.604,6.458 0.313,0.198 10 false G9 2.302,6.448 4.156,6.646 1.854,0.198 10 false Transmission Control Switch 0.396,5.76 2.021,5.958 1.625,0.198 10 false from RH ECU-IG Fuse 0.208,3.292 1.896,3.49 1.688,0.198 10 false from GAUGE NO. 2 Fuse 2.313,4.667 2.625,4.865 0.313,0.198 10 false D4 2.313,4.854 4.135,5.052 1.823,0.198 10 false Park/Neutral Position Switch 5.604,1.208 6.021,1.406 0.417,0.198 10 false STAR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (NEUTRAL POSITION SW SIGNAL AND SHIFT SW STATUS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the tester, read the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
Shift lever in P or N: ON
Shift lever not in P or N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever in R: ON
Shift lever not in R: OFF
Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever in P: ON
Shift lever not in P: OFF
Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever in N: ON
Shift lever not in N: OFF
Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever in D or M: ON
Shift lever not in D or M: OFF

Result
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING INTELLIGENT TESTER (Sports Mode Selection SW)

B

8.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
2.READ VALUE USING INTELLIGENT TESTER (Sports Mode Selection SW)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List.


b.

In accordance with the display on the tester, read the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sports Mode Selection SW Transmission control switch status/
ON or OFF
Shift lever in M: ON
Shift lever not in M: OFF
-

Result
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
3.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
a.
U189486E02
2.042,1.083 2.615,0.573 false 0.063,0.083 0.375,0.281 0.313,0.198 10 false *1 2.646,0.417 2.958,0.615 0.313,0.198 10 false IG 0.448,0.99 0.823,1.219 0.375,0.229 10 false G9

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G9-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G9-6 (IG) - Body ground Engine switch off Below 1 V


Text in Illustration
*1 Front view of wire harness connector
(to Transmission Control Unit Assembly
(to Transmission Control Switch))



OK

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

CHECK POWER SOURCE CIRCUIT

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C199170E40
1.448,0.948 0.875,0.438 true 0.885,1.729 1.458,1.219 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *1 0.771,1.688 1.083,1.885 0.313,0.198 10 false S 0.708,0.313 1.021,0.51 0.313,0.198 10 false IG

Disconnect the transmission control switch connector of the shift lock control unit assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (IG) - 13 (S) Shift lever in M, "+" or "- " Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Transmission Control Unit Assembly
(Transmission Control Switch))



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D2-74 (S) - G9-13 (S) Always Below 1 Ω
D2-74 (S) - Body ground Always 10 kΩ or higher
G9-13 (S) - Body ground Always 10 kΩ or higher




OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)

6.REPLACE ECM

NEXT

7.PERFORM INITIALIZATION
7.PERFORM INITIALIZATION
NOTICE:
·

Performing reset memory/initialization will clear the learned values of both the yaw rate (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, deceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Brake actuator assembly (Skid control ECU) (w/o VSC)

·

Yaw rate sensor (w/ VSC)

·

Deceleration sensor (w/o VSC)



·

After performing reset memory, always perform yaw rate sensor (deceleration sensor zero point) calibration first, and then the CVT oil pressure calibration.

·

Always perform zero point calibration with the vehicle on level ground.

·

Do not shake or vibrate the vehicle during zero point calibration.



a.

Using the intelligent tester, perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration (See page Drivetrain>K112 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION).




NEXT

END

8.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
U189484E02
1.615,1.021 1.333,0.333 false 0.406,1.031 0.781,1.26 0.375,0.229 10 false D4 0.052,0.073 0.365,0.271 0.313,0.198 10 false *1 1.083,0.167 1.396,0.365 0.313,0.198 10 false RB

Disconnect the park/neutral position switch connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D4-1 (RB) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


Text in Illustration
*1 Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C367713E01
1.271,0.99 0.594,0.448 true 1.417,0.969 1.094,0.323 true 1.594,1 1.76,0.344 true 1.844,0.979 2.302,0.406 true 0.813,1.729 1.333,1.25 true 1.427,1.75 1.469,1.271 true 1.896,1.771 1.708,1.24 true 0.458,0.323 0.615,0.521 0.156,0.198 10 false B 0.979,0.146 1.292,0.344 0.313,0.198 10 false PL 1.708,0.167 2.021,0.365 0.313,0.198 10 false RL 2.271,0.24 2.583,0.438 0.313,0.198 10 false RB 0.083,0.073 0.396,0.271 0.313,0.198 10 false *1 0.74,1.698 0.896,1.896 0.156,0.198 10 false L 1.365,1.781 1.677,1.979 0.313,0.198 10 false NL 1.865,1.802 2.177,2 0.313,0.198 10 false DL

Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D or M Below 1 Ω
Shift lever not in D or M 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Park/Neutral Position Switch)



OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D3-2 (RL) - D2-53 (R) Always Below 1 Ω
D3-4 (B) - D2 (STAR) Always Below 1 Ω
D3-3 (PL) - D2-73 (P) Always Below 1 Ω
D3-7 (DL) - D2-56 (D) Always Below 1 Ω
D3-8 (NL) - D2-54 (N) Always Below 1 Ω
D2-52 (STAR) - Body ground Always 10 kΩ or higher
D2-56 (D) - Body ground Always 10 kΩ or higher
D2-54 (N) - Body ground Always 10 kΩ or higher
D2-53 (R) - Body ground Always 10 kΩ or higher
D2-73 (P) - Body ground Always 10 kΩ or higher




OK

11.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)

11.REPLACE ECM

NEXT

12.PERFORM INITIALIZATION
12.PERFORM INITIALIZATION
NOTICE:
·

Performing reset memory/initialization will clear the learned values of both the yaw rate (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, deceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Brake actuator assembly (Skid control ECU) (w/o VSC)

·

Yaw rate sensor (w/ VSC)

·

Deceleration sensor (w/o VSC)



·

After performing reset memory, always perform yaw rate sensor (deceleration sensor zero point) calibration first, and then the CVT oil pressure calibration.

·

Always perform zero point calibration with the vehicle on level ground.

·

Do not shake or vibrate the vehicle during zero point calibration.



a.

Using the intelligent tester, perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration (See page Drivetrain>K112 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION).




NEXT

END