Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0720  Output Speed Sensor Circuit  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NOUT) installed to the continuously variable transaxle and determines the output shaft (secondary pulley) speed in order to control the gear ratio.

The transmission revolution sensor (NOUT) detects the continuously variable transaxle output shaft (secondary pulley) speed and sends a signal to the ECM.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0720
1.

A transmission revolution (NOUT) signal malfunction is not detected.

2.

The transmission revolution sensor (NOUT) output voltage is less than 0.1 V, or higher than 1.9 V.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NOUT) circuit

·

Transmission revolution sensor (NOUT)

·

ECM


P0722
1.

The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch.

2.

The speed indicated by the transmission revolution sensor (NOUT) is less than 300 rpm.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NOUT) circuit

·

Transmission revolution sensor (NOUT)

·

ECM



MONITOR DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NOUT) installed to the continuously variable transaxle and determines the output shaft (secondary pulley) speed in order to control the gear ratio.

If the ECM detects no signal from the transmission revolution sensor (NOUT) even while the vehicle is moving, it will determine that the transmission revolution sensor (NOUT) is malfunctioning, illuminate the MIL and store a DTC.

WIRING DIAGRAM

C200616E34
5.811,2.921 6.121,3.123 0.310,0.202 10 D2 5.811,3.108 6.201,3.310 0.390,0.202 10 ECM 5.637,1.194 6.104,1.396 0.467,0.202 10 NOTO 5.256,2.035 5.533,2.237 0.277,0.202 10 103 5.256,1.058 5.555,1.260 0.299,0.202 10 126 5.637,2.164 6.127,2.366 0.490,0.202 10 NOTB 2.22,1.06 2.694,1.262 0.473,0.202 10 NOTO 2.747,2.035 2.973,2.237 0.226,0.202 10 2 2.747,1.058 2.949,1.260 0.202,0.202 10 1 2.22,2.033 2.712,2.235 0.491,0.202 10 NOTB 0.744,2.66 1.054,2.862 0.310,0.202 10 D65 0.744,2.847 3.351,3.049 2.606,0.202 10 Transmission Revolution Sensor (NOUT)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SPD (NOUT) AND NOUT SENSOR VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NOUT) Secondary pulley speed (NOUT)/
min.: 0 rpm
max.: 12750 rpm
·

0 rpm: Vehicle stopped

·

Approximately 2800 rpm: Vehicle being driven at approximately 60 km/h (37 mph)


Data is displayed in increments of 50 rpm.
NOUT Sensor Voltage Secondary pulley speed (NOUT) sensor output voltage/
min.: 0.000 V
max.: 4.999 V
0.1 to 1.9 V: Engine idling -

Result
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

B

6.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)
a.
C366273E02
1.302,1.24 1.563,0.802 true 1.427,2.271 1.521,2.073 false 2.125,1.271 1.833,0.833 true 0.292,2.74 0.458,2.625 true 0.833,2.635 1,2.719 true 2.594,3.104 2.438,2.844 false 2.26,3.979 2.49,3.729 false 1.417,4.354 1.677,4.208 false 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.073,1.26 1.521,1.49 0.448,0.229 10 false NOTB 2.031,1.292 2.5,1.521 0.469,0.229 10 false NOTO 2.573,3.125 2.885,3.323 0.313,0.198 10 false *1 1.313,2.292 1.625,2.49 0.313,0.198 10 false *2 2.469,3.563 2.781,3.76 0.313,0.198 10 false *b 1.281,4.344 1.594,4.542 0.313,0.198 10 false *c 0.135,2.698 0.448,2.896 0.313,0.198 10 false *2 1.052,2.688 1.365,2.885 0.313,0.198 10 false *1

Remove the transmission revolution sensor (NOUT) (See page Drivetrain>K112 (CVT)>SPEED SENSOR>REMOVAL).


b.

Connect the battery to the transmission revolution sensor (NOUT) as shown in the illustration.


c.

Wave a magnetic object left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NOUT) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change unless the magnetic object is moved as shown in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low signal 4 to 8 mA
1 (NOTO) - 2 (NOTB) High signal 12 to 16 mA


Text in Illustration
*1 Battery
*2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NOUT))
*b Magnet
*c 5 mm or less



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NOUT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)
a.

Disconnect the D65 transmission revolution sensor (NOUT) connector.


b.

Disconnect the D2 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D65-1 (NOTO) - D2-126 (NOTO) Always Below 1 Ω
D65-2 (NOTB) - D2-103 (NOTB) Always Below 1 Ω
D65-1 (NOTO) or D2-126 (NOTO) - Body ground and other terminals Always 10 kΩ or higher
D65-2 (NOTB) or D2-103 (NOTB) - Body ground and other terminals Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.PERFORM INITIALIZATION
6.REPLACE ECM

NEXT

7.PERFORM INITIALIZATION