Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0715  Input/Turbine Speed Sensor "A" Circuit  P0717  Input/Turbine Speed Sensor "A" Circuit No Signal  


DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NT) installed to the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.

The transmission revolution sensor (NT) detects the input turbine speed and sends a signal to the ECM.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0715
1.

A transmission revolution sensor (NT) signal malfunction is not detected.

2.

The transmission revolution sensor (NT) output voltage is less than 0.1 V, or higher than 1.9 V.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NT) circuit

·

Transmission revolution sensor (NT)

·

ECM


P0717
1.

The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch.

2.

The speed indicated by the transmission revolution sensor (NT) is less than 300 rpm.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NT) circuit

·

Transmission revolution sensor (NT)

·

ECM



MONITOR DESCRIPTION

The transmission revolution sensor (NT) is used to detect the input turbine speed. The ECM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input turbine speed) and transmission revolution sensor (NOUT) (output shaft speed) signals.

When the output shaft speed is higher than the expected value and the input turbine speed is less than 300 rpm while driving with the shift lever in D, the ECM will determine that the transmission revolution sensor (NT) is malfunctioning, illuminate the MIL and store a DTC.

WIRING DIAGRAM

C200616E35
5.75,2.958 6.063,3.156 0.313,0.198 10 false D2 5.75,3.135 6.135,3.333 0.385,0.198 10 false ECM 5.625,1.24 6.104,1.479 0.479,0.24 10 false NTO 5.229,2.073 5.615,2.302 0.385,0.229 10 false 124 5.229,1.115 5.625,1.333 0.396,0.219 10 false 125 5.615,2.208 6.094,2.458 0.479,0.25 10 false NTB 2.333,1.125 2.823,1.344 0.49,0.219 10 false NTO 2.76,2.083 2.99,2.281 0.229,0.198 10 false 2 2.75,1.125 2.948,1.323 0.198,0.198 10 false 1 2.344,2.094 2.813,2.354 0.469,0.26 10 false NTB 0.833,2.719 1.146,2.917 0.313,0.198 10 false D68 0.833,2.906 3.385,3.198 2.552,0.292 10 false Transmission Revolution Sensor (NT)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SPD (NT) AND NT SENSOR VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed/
min.: 0 rpm
max.: 12750 rpm
·

Equal to engine speed: Lock-up on (After warming up engine)

·

Nearly equal to engine speed: Lock-up off (Engine idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in R


Data is displayed in increments of 50 rpm.
NT Sensor Voltage Input turbine speed (NT) sensor output voltage/
min.: 0.000 V
max.: 4.999 V
0.1 to 1.9 V: Engine idling -

Result
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

B

6.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.
C366273E01
1.302,1.24 1.563,0.802 true 1.427,2.271 1.521,2.073 false 2.125,1.271 1.833,0.833 true 0.292,2.74 0.458,2.625 true 0.833,2.635 1,2.719 true 2.594,3.104 2.438,2.844 false 2.26,3.979 2.49,3.729 false 1.417,4.354 1.677,4.208 false 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.115,1.26 1.427,1.458 0.313,0.198 10 false NTB 2.031,1.292 2.344,1.49 0.313,0.198 10 false NTO 2.573,3.125 2.885,3.323 0.313,0.198 10 false *1 1.313,2.292 1.625,2.49 0.313,0.198 10 false *2 2.469,3.563 2.781,3.76 0.313,0.198 10 false *b 1.281,4.344 1.594,4.542 0.313,0.198 10 false *c 0.135,2.698 0.448,2.896 0.313,0.198 10 false *2 1.052,2.688 1.365,2.885 0.313,0.198 10 false *1

Remove the transmission revolution sensor (NT) (See page Drivetrain>K112 (CVT)>SPEED SENSOR>REMOVAL).


b.

Connect the battery to the transmission revolution sensor (NT) as shown in the illustration.


c.

Wave a magnetic object left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NT) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change unless the magnetic object is moved as shown in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
1 (NTO) - 2 (NTB) High signal 12 to 16 mA


Text in Illustration
*1 Battery
*2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NT))
*b Magnet
*c 5 mm or less



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)
a.

Disconnect the D68 transmission revolution sensor (NT) connector.


b.

Disconnect the D2 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D68-1 (NTO) - D2-125 (NTO) Always Below 1 Ω
D68-2 (NTB) - D2-124 (NTB) Always Below 1 Ω
D68-1 (NTO) or D2-125 (NTO) - Body ground and other terminals Always 10 kΩ or higher
D68-2 (NTB) or D2-124 (NTB) - Body ground and other terminals Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.PERFORM INITIALIZATION
6.REPLACE ECM

NEXT

7.PERFORM INITIALIZATION