Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2014.09–2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0717  Input/Turbine Speed Sensor "A" Circuit No Signal  


DESCRIPTION

The ECM receives a signal from the turbine speed sensor (transmission revolution sensor (NT)) installed in the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.

The transmission revolution sensor (NT) detects the continuously variable transaxle input shaft speed and sends it to the ECM.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0717
1.

The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch.

2.

The speed indicated by the transmission revolution sensor (NT) is less than 300 rpm.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NT) circuit

·

Transmission revolution sensor (NT)

·

ECM



MONITOR DESCRIPTION

The turbine speed sensor detects the transaxle input shaft speed. The ECM determines the necessary gear ratio based on a comparison of the turbine speed sensor (input shaft speed) with the output speed sensor (output shaft speed).

When the output shaft speed is higher than the expected value and the input shaft speed is less than 300 rpm while driving with the shift lever in D, the ECM will conclude that there is a malfunction in the transmission revolution sensor (NT). The ECM will illuminate the MIL and store the DTCs.

WIRING DIAGRAM

C200870E24
5.781,2.927 6.094,3.125 0.313,0.198 10 false D2 5.781,3.104 6.167,3.302 0.385,0.198 10 false ECM 5.625,1.24 6.042,1.438 0.417,0.198 10 false NT+ 5.25,2.344 5.531,2.542 0.281,0.198 10 false 103 5.25,1.365 5.552,1.563 0.302,0.198 10 false 126 5.625,2.208 6.115,2.406 0.49,0.198 10 false NT- 2.354,1.125 2.708,1.323 0.354,0.198 10 false NT+ 2.729,2.333 2.958,2.531 0.229,0.198 10 false 1 2.75,1.354 2.948,1.552 0.198,0.198 10 false 2 2.375,2.083 2.75,2.281 0.375,0.198 10 false NT- 0.76,2.656 1.073,2.854 0.313,0.198 10 false D68 0.76,2.844 3.177,3.042 2.417,0.198 10 false Transmission Revolution Sensor (NT)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SPD (NT))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed/
min.: 0 rpm
max.: 12750 rpm
·

Lock-up on (After warming up engine): Input turbine speed (NT) equal to engine speed

·

Lock-up off (Idling with shift lever in P or N): Input turbine speed (NT) nearly equal to engine speed

·

Vehicle stopped with shift lever in R: 0 rpm


Data is displayed in increments of 50 rpm.

Result
Result Proceed to
Data displayed is not as specified under Normal Condition A
Data displayed is as specified under Normal Condition B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

B

6.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.
C200614E24
1.281,1.698 1.583,1.177 true 2.146,1.698 1.844,1.177 true 0.063,0.063 0.302,0.26 0.24,0.198 10 false *1 1.094,1.729 1.542,1.927 0.448,0.198 10 false NT+ 2.125,1.729 2.573,1.927 0.448,0.198 10 false NT-

Disconnect the transmission revolution sensor (NT) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NT-) - 2 (NT+) 20°C (68°F) 560 to 680 Ω


Text in Illustration
*1 Component without harness connected
(Transmission Revolution Sensor (NT))



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D2-126 (NT+) - D2-103 (NT-) 20°C (68°F) 560 to 680 Ω
D2-126 (NT+) - Body ground Always 10 kΩ or higher
D2-103 (NT-) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.PERFORM INITIALIZATION
6.REPLACE ECM

NEXT

7.PERFORM INITIALIZATION