Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0841  Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance  P2829  Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS)  


DESCRIPTION

The ECM controls the secondary oil pressure calibration based on the secondary oil pressure signal detected by the oil pressure sensor.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0841
1.

The requested oil pressure value is 0.5 MPa or less.

2.

The oil pressure sensor output value is 3.0 MPa or higher.

3.

3 seconds

4.

1 trip detection logic


·

Oil pressure sensor

·

Continuously variable transaxle assembly

·

ECM


P2829
1.

The requested oil pressure value is 0.5 MPa or less.

2.

The oil pressure sensor output value is 3.0 MPa or higher.

3.

3 seconds

4.

1 trip detection logic


1.

The vehicle is driven at a speed of 8 km/h (5 mph) or less with the shift lever in D.

2.

The ratio of the rotation speeds of the primary pulley (NIN) and secondary pulley (NOUT) exceeds the threshold.

3.

0.2 seconds

4.

2 trip detection logic



MONITOR DESCRIPTION

The ECM checks for belt clamping high-pressure errors. When a mechanical malfunction is detected in the shift solenoid valve SLS and in the oil pressure sensor, the ECM detects the problem, illuminates the MIL and stores the DTC.

PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0841 AND P2829)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
Only P0841 and/or P2829 is output A
P0841 and/or P2829 and other DTCs are output B

HINT:

If any other DTCs besides P0841 or P2829 are output, perform troubleshooting for those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (A/T OIL PRESSURE)

B

2.READ VALUE USING INTELLIGENT TESTER (A/T OIL PRESSURE)

A

3.REPLACE OIL PRESSURE SENSOR

B

3.REPLACE OIL PRESSURE SENSOR

NEXT

4.CLEAR DTC
4.CLEAR DTC

NEXT

5.PERFORM INITIALIZATION
5.PERFORM INITIALIZATION

NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
P0841 and/or P2829 is output A
DTC is not output B



A

7.REPLACE ECM

B

END

7.REPLACE ECM

NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION

NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
P0841 and/or P2829 is output A
DTC is not output B



A

10.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

END

10.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NEXT

11.CLEAR DTC
11.CLEAR DTC

NEXT

12.PERFORM INITIALIZATION