Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292052 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 30400E 1.INSTALL CVT OIL PUMP TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands, and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.


b.

Temporarily attach the CVT oil pump type T oil seal by pressing it onto the installation surface of the oil pump housing by hand.


c.
C208789E13
1.813,1.802 1.813,2.479 false 1.708,2.5 2.01,2.823 0.302,0.323 10 false SST

Clean the oil seal contact section of SST and the area around it.


d.

Using SST, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the oil pump housing.

SST
09309-36010  

NOTICE:
·

Drive the oil seal in gradually, while visually checking that it is even.

·

After the installation, confirm that the oil seal has been driven in until it is even with the side surface of the oil pump housing.

·

Wipe any extra grease off with your hand.



HINT:

The oil seal should be driven in between 0 to 0.5 mm (0 to 0.0197 in.) as measured from the side surface of the oil pump housing.



Hide 32000A 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.

Clean the drive plate and torque converter assembly setting bolt holes.


b.
C202919E03
2.427,0.694 2.544,0.850 0.117,0.156 10 A 2.427,0.694 2.544,0.850 0.117,0.156 10 A 0.196,0.292 0.374,0.448 0.178,0.156 10 *1 2.501,1.463 2.680,1.619 0.178,0.156 10 *1 0.826,2.8 1.004,2.956 0.178,0.156 10 *2 2.434,2.105 2.612,2.261 0.178,0.156 10 *2 0.395,0.382 0.493,0.382 0.493,0.382 0.631,0.704 false 1.365,2.32 1.193,2.878 1.193,2.878 1.039,2.878 false 2.587,1.204 2.587,1.443 false 2.904,1.842 2.764,2.191 2.764,2.191 2.633,2.191 false

Using a vernier caliper and straightedge, measure dimension "A" between the transaxle contact surface of the engine*1 and the torque converter assembly contact surface of the drive plate*2. (#)

NOTICE:

Make sure to deduct the thickness of the straightedge.



c.
C211788E03
1.917,0.26 3.052,0.26 true 1.906,0.958 3.042,0.958 true 3.094,0.177 3.25,0.344 0.156,0.167 10 false *a 3.073,0.875 3.229,1.042 0.156,0.167 10 false *b

Turn the front oil pump drive gear so that the groove is at the top and put a matchmark on the housing.

Text in Illustration
*a Matchmark
*b Groove


d.
C169591E11
1.438,1.896 1.521,1.896 1.521,1.896 1.708,1.615 true 1.927,0.115 1.854,0.115 1.854,0.115 1.75,0.271 false 1.969,0.042 2.24,0.208 0.271,0.167 10 false *a 1.271,1.823 1.448,1.979 0.177,0.156 10 false *b

Put a matchmark on the torque converter assembly so that the position of its key is clearly indicated.

Text in Illustration
*a Key
*b Matchmark


e.
C225323E01
1.275,0.374 1.723,0.176 1.723,0.176 1.275,0.593 false 1.753,0.062 1.931,0.220 0.178,0.158 10 *a

Align the matchmark on the housing with the one on the torque converter assembly and mesh the splines of the input shaft with the turbine runner splines.

Text in Illustration
*a Matchmark

NOTICE:

Install the torque converter assembly horizontally to the input shaft.



f.
C225324E02
1.271,1 0.938,0.365 0.938,0.365 0.802,0.365 false 1.26,2.135 0.927,2.771 0.927,2.771 0.792,2.771 true 2.49,1.552 1.74,2.823 1.74,2.823 2.51,1.865 true 2.948,1.51 2.063,0.448 2.063,0.448 2.917,1.688 true 0.625,0.271 0.802,0.427 0.177,0.156 10 false *a 0.625,2.688 0.802,2.844 0.177,0.156 10 false *a 1.573,2.781 1.75,2.938 0.177,0.156 10 false *b 1.917,0.292 2.094,0.448 0.177,0.156 10 false *b

Rotate the torque converter assembly and mesh the splines of the stator shaft with the stator splines.

Text in Illustration
*a Matchmark
*b Oil Seal

NOTICE:
·

Do not damage the oil seal.

·

Install the torque converter assembly horizontally to the input shaft.



HINT:

Rotate the torque converter assembly approximately 180°.



g.
C225325E02
1.26,1.073 0.771,0.563 0.771,0.563 1.26,1.292 true 2.458,1.583 1.594,2.927 1.594,2.927 2.479,1.896 true 2.833,1.729 2.188,0.563 2.188,0.563 2.854,1.563 true 0.625,0.406 0.792,0.573 0.167,0.167 10 false *a 2.073,0.396 2.24,0.563 0.167,0.167 10 false *b 1.448,2.906 1.615,3.073 0.167,0.167 10 false *b

Rotate the torque converter assembly again, align the matchmark on the housing with the one on the torque converter assembly and fit the key of the torque converter assembly into the groove of the oil pump drive gear.

Text in Illustration
*a Matchmark
*b Oil Seal

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the oil seal.

·

Install the torque converter assembly horizontally to the input shaft.




h.
C192348E01
2.361,0.343 2.484,0.493 0.123,0.150 10 B

Using a vernier caliper and straightedge, measure dimension "B" shown in the illustration and check that dimension "B" is greater than dimension "A" (which was measured in step (#)).

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:

Subtract the thickness of the straightedge from the measured value to gain dimension "B".



Hide 12325A 3.INSTALL ENGINE MOUNTING BRACKET LH

a.

Install the engine mounting bracket LH to the continuously variable transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 33823 4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 30400 5.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C195990E09
2.146,0.938 2.052,0.938 2.052,0.938 1.563,1.115 true 2.188,0.854 2.406,1.042 0.219,0.188 10 false *1 1.135,1.031 1.313,1.229 0.177,0.198 10 false *2

Apply clutch spline grease to the circumference of the crankshaft contact surface with the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum spread:

About 1 g (0.0353 oz.)


Text in Illustration
*1 Torque Converter Assembly Centerpiece
*2 Crankshaft


b.
C211789E02
2.583,2.469 2.719,2.625 0.135,0.156 10 false A 2.885,3 3.021,3.156 0.135,0.156 10 false A 1.271,2.573 1.406,2.729 0.135,0.156 10 true A 1.01,2.927 1.146,3.083 0.135,0.156 10 true D 1.021,3.813 1.156,3.969 0.135,0.156 10 true C 1.344,4.083 1.479,4.24 0.135,0.156 10 true C 2.604,4.031 2.76,4.219 0.156,0.188 10 true C 2.729,3.792 2.865,3.948 0.135,0.156 10 false C 2.948,3.542 3.083,3.698 0.135,0.156 10 false B

Confirm that 2 knock pins are on the transaxle contact surface of the engine cylinder block before transaxle installation.


c.

Apply adhesive to the threads of a new bolt D.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Maintain the engine and continuously variable transaxle assembly in a horizontal position, align the knock pins with each hole on the continuously variable transaxle assembly and install the continuously variable transaxle assembly with the 9 bolts shown in the illustration.

Torque:
Bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt B : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Bolt C : 44 N*m (449 kgf*cm, 32 ft.*lbf)
Bolt D : 28 N*m (286 kgf*cm, 21 ft.*lbf)

Bolt length:
Bolt A:

55 mm (2.17 in.)

Bolt B:

65 mm (2.56 in.)

Bolt C:

32 mm (1.26 in.)

Bolt D:

38 mm (1.50 in.)


HINT:

Bolts A and B: Install from transaxle side

Bolts C and D: Install from engine side


NOTICE:
·

Do not use excessive force when installing the continuously variable transaxle assembly.

·

Make sure that the torque converter assembly rotates.

·

Do not reuse bolt D.

·

Before applying adhesive to bolt D, remove any sealant from its installation hole in the continuously variable transaxle assembly.

·

After installing bolt D, leave the continuously variable transaxle assembly at least 1 hour.




e.

Clean the installation holes for the drive plate and torque converter assembly setting bolts.


f.
A057108

Apply a few drops of adhesive to 2 or 3 threads of the 6 drive plate and torque converter assembly setting bolt tips.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



g.

Install the 6 drive plate and torque converter assembly setting bolts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored bolt, and then the 5 remaining silver colored bolts.



Hide 11361J 6.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the engine assembly.


Hide 33493B 7.INSTALL OIL COOLER

a.

Install the oil cooler to the continuously variable transaxle assembly with the 3 bolts.

Torque:
12 N*m (120 kgf*cm, 8 ft.*lbf)


b.

Connect the 2 water by-pass hoses to the oil cooler and engage the 2 clamps.


c.

Install the 2 oil cooler hoses to the oil cooler and continuously variable transaxle assembly and engage the 4 clamps.


Hide 8.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C225343E03
2.031,0.563 2.281,0.25 2.281,0.25 2.365,0.25 true 2.396,0.177 2.573,0.333 0.177,0.156 10 false *1 1.396,0.073 1.542,0.229 0.146,0.156 10 false A 0.948,0.854 1.094,1.01 0.146,0.156 10 true B

Install the shift cable bracket and 2 wire harness clamp brackets to the continuously variable transaxle assembly with the 2 bolts.

Torque:
Bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
Bolt B : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


b.

Install the ground cable to the wire harness clamp bracket with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

Text in Illustration
*1 Ground Cable


Hide 82121 9.INSTALL ENGINE WIRE

a.

Install the 2 wire harness clamps and connect the oil pressure sensor connector to the continuously variable transaxle assembly.


b.

Install the 4 wire harness clamps and connect the 3 revolution sensor connectors, park/neutral position switch connector and transmission wire connector to the continuously variable transaxle assembly.


Hide 28100 10.INSTALL STARTER ASSEMBLY

a.

Install the starter assembly to the continuously variable transaxle assembly with the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


b.

Connect the connector to the starter assembly.


c.

Install the nut and cover the nut with the terminal cap.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 12321A 11.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Install the rear engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12311A 12.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 13.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 14.RESET MEMORY

a.

Perform Reset Memory (CVT initialization) when replacing the continuously variable transaxle assembly (See page Drivetrain>K112 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION).