Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.05
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291835 ENGINE ASSEMBLY A

2AZ-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32101 1.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A126932E01
1.087,1.621 1.444,1.797 0.357,0.177 10 SST 1.442,1.124 1.267,1.59 1.267,1.59 1.839,1.317 false

Using SST, hold the crankshaft pulley.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A114342

Install the front spacer.

HINT:

Align the pin of the front spacer with the pin hole of the crankshaft.



c.
A129332E05
2.32,2.582 2.506,2.742 0.186,0.160 10 *2 2.296,2.662 2.183,2.662 2.183,2.662 2.482,3.581 false 0.726,0.265 0.924,0.428 0.198,0.163 10 *1 0.984,0.361 1.382,0.361 false

Install the drive plate and ring gear sub-assembly and rear spacer onto the crankshaft.

Text in Illustration
*1 Drive Plate and Ring Gear Sub-Assembly
*2 Rear Spacer
V100135

Transaxle


d.

Clean the 8 bolts and 8 bolt holes.


e.

Apply adhesive to 2 or 3 threads of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1342, Three Bond 1342 or equivalent



f.
A112224E07
2.094,0.406 2.219,0.563 0.125,0.156 10 true 1 1.865,1.688 1.99,1.844 0.125,0.156 10 true 2 1.417,1.031 1.542,1.188 0.125,0.156 10 true 3 2.521,1.104 2.646,1.26 0.125,0.156 10 true 4 1.646,0.573 1.771,0.729 0.125,0.156 10 true 5 2.281,1.573 2.406,1.729 0.125,0.156 10 true 6 2.458,0.708 2.583,0.865 0.125,0.156 10 true 7 1.479,1.417 1.604,1.573 0.125,0.156 10 true 8

In several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate and ring gear sub-assembly.



Hide 30500 2.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)

Hide 30400 3.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 16282D 4.CONNECT NO. 5 WATER BY-PASS HOSE (for CVT)

a.

Connect the No. 5 water by-pass hose.


Hide 43457 5.INSTALL DRIVE SHAFT BEARING BRACKET

a.
A098759

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 82121 6.CONNECT ENGINE WIRE

a.
U188345E01
1.32,1.558 1.705,1.742 0.385,0.184 10 30° 0.696,1.558 1.081,1.742 0.385,0.184 10 30°

Install the engine wire harness cover with the 2 bolts as shown in the illustration.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


b.

Install the ground cable with the bolt as shown in the illustration.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

HINT:

The ground cable can be set to within 30° on either side of the prescribed position.



c.
U188337E02
1.438,0.438 1.656,0.583 0.219,0.146 0.313,0.146 0.458,0.333 0.146,0.188 10 false A 0.219,1.479 0.365,1.667 0.146,0.188 10 false B 0.833,1.833 0.979,2.021 0.146,0.188 10 false C 1.063,0.833 1.208,1.021 0.146,0.188 10 false D 2.76,0.417 2.906,0.604 0.146,0.188 10 false E

Connect the radio setting condenser connector (A), oil pressure sensor connector (B), engine coolant temperature sensor connector (C), heated oxygen sensor connector (D) and camshaft position sensor connector (E).


d.

Connect the 4 ignition coil connectors.


e.
A132644

Connect the camshaft timing oil control valve connector.


f.

Install the ground cable (A) and 3 engine wire harness clamps (B) with the 4 bolts as shown in the illustration.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

U188346E02
0.188,0.146 0.344,0.313 0.156,0.167 10 false A 5.708,0.219 5.865,0.385 0.156,0.167 10 false B 5.708,2.375 5.865,2.552 0.156,0.177 10 false B 0.229,0.833 0.583,1.031 0.354,0.198 10 false 45° 0.635,1.208 0.99,1.406 0.354,0.198 10 false 45°


g.
A132645

Connect the knock sensor connector.


Hide 17135A 7.INSTALL NO. 1 INTAKE MANIFOLD INSULATOR

Hide 23250 9.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807 10.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 12262 11.INSTALL NO. 2 VENTILATION HOSE

Hide 12.INSTALL ENGINE ASSEMBLY

a.

Set an engine lifter underneath the engine assembly.

HINT:

Set wooden blocks or equivalent under the engine assembly, so that the engine assembly is level.



b.

Carefully install the engine assembly to the vehicle.

NOTICE:

While installing the engine assembly to the vehicle, do not allow it to contact the vehicle.



Hide 13.SUSPEND ENGINE ASSEMBLY

a.
A132560E04
2.167,0.604 2.698,0.76 false 1,2.469 1,2.688 false 0.156,2.708 1.521,3.333 1.365,0.625 10 true No. 1 Engine Hanger 0.75,0.49 2.135,0.906 1.385,0.417 10 true No. 2 Engine Hanger

Install the No. 1 and No. 2 engine hangers with the bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

Part No.:
Item Part No.
No. 1 engine hanger 12281-28010 or
12281-0H010
No. 2 engine hanger 12282-28010 or
12282-0H010
Bolt 91552-81020 or
90105-C0076



b.

Attach a sling device to the engine hangers and chain block.


c.

Remove the engine lifter.


Hide 12372A 14.INSTALL ENGINE MOUNTING INSULATOR LH

a.
A124845

Install the engine mounting insulator LH with the 4 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


b.
A287186E02
0.708,1.573 1,1.75 0.292,0.177 10 true Nut 2.104,1.688 2.99,2.052 0.885,0.365 10 true Through Bolt

Install the through bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

HINT:

Install the through bolt by tightening the nut.



Hide 12305 15.INSTALL ENGINE MOUNTING INSULATOR RH

a.
U188338E02
2.885,0.406 3.073,0.594 0.188,0.188 10 false A 1.854,0.083 2.042,0.271 0.188,0.188 10 false B

Install the engine mounting insulator RH with the 2 nuts and 2 bolts.

Torque:
Bolt : 95 N*m (969 kgf*cm, 70 ft.*lbf)
Nut A : 95 N*m (969 kgf*cm, 70 ft.*lbf)
Nut B : 52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12281A 16.REMOVE ENGINE HANGER

a.

Remove the chain block, sling device and No. 1 and No. 2 engine hangers.


Hide 51201 17.TEMPORARILY TIGHTEN FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Temporarily install the front suspension crossmember sub-assembly with the 2 bolts.

A132565


Hide 51403B 18.TEMPORARILY TIGHTEN FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY

a.

Temporarily install the front suspension member brace sub-assembly LH and front suspension member brace sub-assembly RH with the 4 bolts (B) and 2 bolts (A).

U188343E02
2.417,1.625 2.542,1.781 0.125,0.156 10 false A 4.625,1.625 4.75,1.781 0.125,0.156 10 false A 3.906,0.458 4.042,0.615 0.135,0.156 10 false B 5.458,0.5 5.594,0.656 0.135,0.156 10 false B 3.156,0.458 3.292,0.615 0.135,0.156 10 false B 1.594,0.458 1.729,0.615 0.135,0.156 10 false B


Hide 51201 19.TIGHTEN FRONT SUSPENSION CROSSMEMBER AND FRONT SUSPENSION CROSSMEMBER BRACE

a.

Alternately insert SST into the standard holes on the front suspension crossmember sub-assembly RH and front suspension crossmember sub-assembly LH and properly align the front suspension crossmember sub-assembly. Then install the bolts (A) and (B), and tighten them to the specification in several passes.

SST
09670-00010  

Torque:
Bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
Bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)

NOTICE:
·

SST must be inserted perpendicularly into the standard holes.

·

If SST cannot be perpendicularly inserted, loosen the 8 bolts and try again.



U188347E02
1.698,1.135 2.74,0.688 true 4.427,0.667 5.458,1.115 true 5.542,5.365 5.667,5.521 0.125,0.156 10 false A 1.5,5.365 1.625,5.521 0.125,0.156 10 false A 2.396,4.688 2.521,4.844 0.125,0.156 10 false A 4.625,4.688 4.75,4.844 0.125,0.156 10 false A 1.552,3.531 1.688,3.688 0.135,0.156 10 false B 3.146,3.5 3.281,3.656 0.135,0.156 10 false B 3.885,3.51 4.021,3.667 0.135,0.156 10 false B 5.5,3.531 5.635,3.688 0.135,0.156 10 false B 0.375,2.5 1.115,2.677 0.74,0.177 10 false CORRECT 1.396,2.5 2.292,2.677 0.896,0.177 10 false INCORRECT 4.885,2.5 5.625,2.677 0.74,0.177 10 false CORRECT 5.917,2.5 6.813,2.677 0.896,0.177 10 false INCORRECT 2.813,0.604 3.135,0.781 0.323,0.177 10 false SST 4.094,0.573 4.417,0.75 0.323,0.177 10 false SST


Hide 57104E 20.INSTALL FRONT CROSSMEMBER SUB-ASSEMBLY

a.

Install the front crossmember sub-assembly with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)

A132563


Hide 12371A 21.INSTALL REAR ENGINE MOUNTING INSULATOR

a.
A124842

Install the rear engine mounting insulator with the 2 nuts and 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


b.
A132533

Install the through bolt which is used to secure the rear engine mounting insulator into the rear engine mounting bracket.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12361A 22.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.
A124840

Install the front engine mounting insulator with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


b.
A124839E03
2.24,0.958 3.063,1.333 0.823,0.375 10 true Through Bolt 1.042,1.74 1.292,1.917 0.25,0.177 10 false Nut

Install the through bolt and nut which is used to secure the front engine mounting bracket.

T = 145 N*m{ 1,479 kgf*cm 107 ft.*lbf }


Hide 43410 23.INSTALL FRONT DRIVE SHAFT

a.

Install the front drive shaft (See page Drivetrain>DRIVE SHAFT>FRONT DRIVE SHAFT ASSEMBLY>INSTALLATION).


Hide 45025D 24.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
U189026E01
0.257,0.365 0.410,0.577 0.153,0.211 10 A 2.457,1.647 2.610,1.858 0.153,0.211 10 B

Insert clip B, set clip A on the upper surface of the panel and connect the No. 1 steering column hole cover sub-assembly to the floor panel.


Hide 45221 25.INSTALL STEERING INTERMEDIATE SHAFT

a.
A132530E02
1.542,2.313 2.219,2.313 false 2.302,2.219 3.063,2.573 0.76,0.354 10 true Matchmark

Align the matchmark on the steering intermediate shaft and steering gear.


b.

Install the steering intermediate shaft with the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 45259A 26.INSTALL COLUMN HOLE COVER SILENCER SHEET

a.
A132529

Install the column hole cover silencer sheet with the 2 clips.


Hide 27.CONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

Hide 88320 29.INSTALL COOLER COMPRESSOR ASSEMBLY

Hide 82121 30.CONNECT ENGINE WIRE

a.
A132525

Install the battery ground cable with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


b.
A132524

Install the engine wire harness cover with the bolt.


c.

Install the ground cable with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


d.
A132613

Install the battery positive (+) cable to the engine room relay block.


e.

Insert the relay block side cover.


f.
A132522

Connect the 2 connectors.


g.

Install the engine room relay block cover.


h.
A132526

Install the engine wire harness clamp with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


i.

Install the ground cable with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


j.

Connect the crankshaft position sensor connector.


Hide 16611 34.INSTALL RADIATOR RESERVOIR BRACKET

a.
A132521

Install the radiator reservoir bracket with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 16470 35.INSTALL RADIATOR RESERVOIR ASSEMBLY

a.
A132520

Install the radiator reservoir assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the No. 1 and No. 2 water by-pass hoses.


Hide 44774 37.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the 2 union to connector tube hoses.


Hide 87246B 38.CONNECT HEATER WATER OUTLET HOSE

a.

Connect the heater water outlet hose (for Automatic Transaxle or CVT (w/ Air Cooled Transmission Oil Cooler)).

A394014E01
0.229,0.156 0.542,0.354 0.313,0.198 10 false *A 4.042,0.167 4.354,0.365 0.313,0.198 10 false *B

Connect the heater water outlet hose (for CVT (w/o Air Cooled Transmission Oil Cooler)).

Text in Illustration
*A for Automatic Transaxle
for CVT (w/ Air Cooled Transmission Oil Cooler)
*B for CVT (w/o Air Cooled Transmission Oil Cooler)


Hide 35104V 39.CONNECT BREATHER PLUG HOSE

a.

Attach the breather plug hose to the clamp.

A287316E01
0.49,0.08 0.729,0.282 0.239,0.202 10 *A 4.128,0.052 4.368,0.254 0.239,0.202 10 *B 0.99,2.547 1.229,2.749 0.239,0.202 10 *c 6.277,2.578 6.516,2.780 0.239,0.202 10 *c 0.742,1.949 0.982,2.152 0.239,0.202 10 *a 4.282,1.948 4.522,2.151 0.239,0.202 10 *b 0.681,1.888 3.334,3.653 2.653,1.765 4.207,1.9 6.86,3.664 2.653,1.765

NOTICE:
·

Make sure that the marking on the water by-pass hose is aligned with the center of the clamp.

·

Make sure that the breather plug hose is positioned on the left side of the vehicle.

·

Make sure that the breather plug is inclined as shown in the illustration.

·

Make sure that the hose is not kinked.



Text in Illustration
*A for Automatic Transaxle
for CVT (w/ Air Cooled Transmission Oil Cooler)
*B for CVT (w/o Air Cooled Transmission Oil Cooler)
*a View from Side of the Vehicle *b View from Front of the Vehicle
*c Horizontal Axis - -


Hide 87245A 40.CONNECT HEATER WATER INLET HOSE

a.

Connect the heater water inlet hose.


Hide 25860 41.CONNECT PURGE LINE HOSE

a.
A234690

Connect the purge line hose.


Hide 74414D 43.INSTALL BATTERY CARRIER SUPPORT

a.
A132517

Install the battery carrier support with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 74411 44.INSTALL BATTERY CARRIER

a.
A132516

Install the battery carrier with the 4 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Connect the wire harness clamp.


Hide 17700 45.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17752 46.INSTALL NO. 2 AIR CLEANER INLET

Hide 17705 47.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 74431 48.INSTALL BATTERY TRAY

Hide 28800 49.INSTALL BATTERY

a.

Install the battery clamp with the bolt and nut.

Torque:
Bolt : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Nut : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the positive (+) cable to the battery positive (+) terminal.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 50.INSTALL COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

Hide 51.CONNECT OIL COOLER HOSE (for Automatic Transaxle)

a.
C202162

Connect the 2 oil cooler hoses to the automatic transaxle assembly.


Hide 32941D 52.CONNECT INLET OIL COOLER HOSE (for CVT)

a.
A284769

w/ Air Cooled Transmission Oil Cooler:

i.

Connect the inlet oil cooler hose to the oil cooler outlet tube.



Hide 32942C 53.CONNECT OUTLET NO.1 OIL COOLER HOSE (for CVT)

a.
A283488

w/ Air Cooled Transmission Oil Cooler:

i.

Connect the outlet No. 1 oil cooler hose to the oil cooler outlet tube.



Hide 16283H 54.CONNECT NO. 6 WATER BY-PASS HOSE (for CVT)

a.
A284862

w/ Air Cooled Transmission Oil Cooler:

i.

Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe.



Hide 16572D 55.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose.


Hide 16571C 56.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose.


Hide 17410 57.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 51217A 58.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.

Install the front suspension member reinforcement RH with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 51218A 59.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)

A132609


Hide 61.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 64.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

a.

Connect the negative (-) cable to the battery negative (-) terminal.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 66.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEVEL (for Automatic Transaxle)

Hide 67.ADJUST CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEVEL (for CVT)

Hide 53292A 68.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 53701 69.INSTALL FRONT FENDER APRON RH

Hide 53702 70.INSTALL FRONT FENDER APRON LH

Hide 51442 71.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 72.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53301 74.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly with the 4 bolts.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 53301 75.ADJUST HOOD SUB-ASSEMBLY

Hide 78.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 79.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



Hide 80.PERFORM REGISTRATION

a.

When replacing the engine assembly, perform vehicle stability control system recognition in the ECM (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>REGISTRATION).


Hide 81.RESET MEMORY

a.

When replacing the engine assembly, perform the RESET MEMORY procedure.

Automatic Transaxle initialization:

See page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION


CVT initialization:

See page Drivetrain>K112 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION