Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM C

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  B2278  Engine Switch Circuit Malfunction  


DESCRIPTION

This DTC is output when 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.

DTC No. DTC Detection Condition Trouble Area
B2278 Communication is abnormal between the main body ECU and engine switch or the engine switch is defective
·

Engine switch

·

Instrument panel junction block LH (Main body ECU)

·

Wire harness or connector



WIRING DIAGRAM

B157543E14
3.373,1.321 3.672,1.486 0.299,0.165 10 SS1 3.742,1.321 3.856,1.486 0.114,0.165 10 7 5.643,1.321 5.850,1.486 0.207,0.165 10 17 5.942,1.41 6.366,1.575 0.424,0.165 10 SSW1 5.942,1.975 6.366,2.140 0.424,0.165 10 SSW2 5.643,1.882 5.850,2.047 0.207,0.165 10 16 3.742,1.886 3.856,2.051 0.114,0.165 10 2 2.63,3.703 2.745,3.868 0.114,0.165 10 5 3.373,1.896 3.672,2.061 0.299,0.165 10 SS2 2.411,3.493 2.757,3.658 0.346,0.165 10 GND 0.917,3.698 1.262,3.863 0.346,0.165 10 G31 0.917,3.871 1.832,4.036 0.915,0.165 10 Engine Switch 2.979,2.499 3.283,2.655 0.304,0.156 10 SS2 2.61,2.499 2.939,2.655 0.329,0.156 10 GND 2.279,2.499 2.583,2.655 0.304,0.156 10 SS1 1.578,2.691 1.901,2.847 0.323,0.156 10 Free 1.314,2.981 2.211,3.136 0.897,0.156 10 Full Traveling 5.824,5.955 6.130,6.121 0.306,0.165 10 G57 5.824,6.119 6.854,6.284 1.031,0.165 10 Main Body ECU

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (START SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Check the DATA LIST for proper functioning of the start switch.

HINT:

When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.


Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
St SW1 Start switch 1 / ON or OFF ON: Engine switch is pushed
OFF: Engine switch is not pushed
-
St SW2 Start switch 2 / ON or OFF ON: Engine switch is pushed
OFF: Engine switch is not pushed
-

OK:

ON (engine switch is pushed) and OFF (engine switch is not pushed) appear on the screen.




OK

2.CHECK ENGINE SWITCH CONDITION

NG

3.INSPECT ENGINE SWITCH
2.CHECK ENGINE SWITCH CONDITION
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

OK:

off → on (ACC) → on (IG) → off


HINT:





OK

END

NG

GO TO OTHER PROBLEM

3.INSPECT ENGINE SWITCH
a.

Remove the engine switch (See page Engine / Hybrid System>2GR-FE STARTING>ENGINE SWITCH>REMOVAL).

A109252E01
3.745,0.332 4.093,0.534 0.348,0.202 10 SS1 5.124,0.332 5.472,0.534 0.348,0.202 10 SS2 4.294,0.332 4.642,0.534 0.348,0.202 10 GND 3.9,0.932 3.9,0.498 false 5.245,0.932 5.245,0.498 false 4.44,0.932 4.44,0.498 false


b.

Disconnect the switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
7 (SS1) - 5 (GND) Pushed Below 1 Ω
2 (SS2) - 5 (GND) Pushed Below 1 Ω
7 (SS1) - 5 (GND) Not pushed 10 kΩ or higher
2 (SS2) - 5 (GND) Not pushed 10 kΩ or higher


HINT:

This switch is a momentary type switch.




OK

4.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)
a.
A393997E01
0.5,1.417 0.917,1.667 0.417,0.25 0.5,3.667 0.917,3.917 0.417,0.25 1.833,1.594 2.479,1.281 false 2.167,1.635 2.469,1.635 false 2.479,1.99 1.396,1.677 false 2.167,3.958 2.563,4.26 false 2.271,3.948 2.583,3.802 false 0.198,0.146 2.479,0.583 2.281,0.438 10 false Front view of wire harness connector: (to Engine Switch) 0.563,1.458 1.146,1.74 0.583,0.281 10 false G31 0.198,2.469 2.448,3 2.25,0.531 10 false Front view of wire harness connector: (to Main Body ECU) 0.563,3.708 1.146,3.99 0.583,0.281 10 false G57 2.531,1.177 3.115,1.458 0.583,0.281 10 false GND 2.531,1.552 3.115,1.833 0.583,0.281 10 false SS1 2.542,1.927 3.125,2.208 0.583,0.281 10 false SS2 2.625,3.719 3.208,4 0.583,0.281 10 false SSW1 2.604,4.188 3.188,4.469 0.583,0.281 10 false SSW2

Disconnect the G57 ECU connector.


b.

Disconnect the G31 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G31-7 (SS1) - G57-17 (SSW1) Always Below 1 Ω
G31-2 (SS2) - G57-16 (SSW2) Always Below 1 Ω
G31-5 (GND) - Body ground Always Below 1 Ω
G31-7 (SS1) or G57-17 (SSW1) - Body ground Always 10 kΩ or higher
G31-2 (SS2) or G57-16 (SSW2) - Body ground Always 10 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR