Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM C

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The skid control ECU converts these signals into 4-pulse signals and sends them to the combination meter. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the main body ECU. The main body ECU determines the vehicle speed based on the frequency of these pulse signals.

The main body ECU and the combination meter are connected by a cable and the CAN. DTC B2282 is output when the cable information and CAN information are inconsistent.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2282 Cable information and CAN information between the main body ECU and the combination meter are inconsistent
·

CAN communication system

·

Combination meter system

·

Instrument panel junction block LH (Main body ECU)

·

Wire harness or connector


B2283 When either of conditions below are met:
·

Over-deceleration in vehicle speed

·

Vehicle speed and engine speed do not match


·

DTC B2282 detection area

·

Combination meter

·

Skid Control ECU

·

Speed sensor

·

Instrument panel junction block LH (Main body ECU)

·

Wire harness or connector



B138069E01
0.273,1.934 1.057,2.241 0.784,0.307 10 From Speed Sensor 1.117,1.518 2.226,1.668 1.109,0.151 10 Skid Control ECU 2.502,1.488 3.048,1.627 0.546,0.139 10 4 pulses 4.676,1.488 5.222,1.627 0.546,0.139 10 4 pulses 3.322,1.16 4.135,1.659 0.813,0.499 10 Combination Meter (Meter ECU) 3.7,2.478 4.019,2.617 0.319,0.139 10 CAN 5.533,1.527 6.549,1.672 1.016,0.145 10 Main Body ECU 4.717,2.929 6.175,3.068 1.458,0.139 10 B2282 Detection Area 2.658,3.37 4.115,3.509 1.458,0.139 10 B2283 Detection Area

WIRING DIAGRAM

B167158E02
5.571,2.699 5.866,2.855 0.295,0.156 10 G59 5.571,2.834 6.588,2.981 1.017,0.147 10 Main Body ECU 0.584,2.699 0.878,2.855 0.295,0.156 10 G28 1.616,2.003 1.799,2.159 0.184,0.156 10 40 5.45,2.003 5.560,2.159 0.110,0.156 10 9 5.665,2.097 5.969,2.252 0.304,0.156 10 SPD 1.336,2.097 1.528,2.252 0.193,0.156 10 +S 0.584,2.834 1.786,2.981 1.202,0.147 10 Combination meter 3.278,1.457 3.897,1.622 0.619,0.165 10 CAN Line

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in an ECU, all systems in the diagram above will not operate normally.



PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check if the function of the speedometer in the combination meter is normal.

Result:
Result Proceed to
Actual vehicle speed and the speed indicated on the speedometer are not the same. A
Actual vehicle speed and the speed indicated on the speedometer are the same. B


HINT:
·

The vehicle speed sensor is functioning normally when the indication on the speedometer is normal.

·

The meter CPU receives vehicle speed signals from the skid control ECU via the CAN communication lines. The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.





A

2.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COMBINATION METER)
2.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

b.

Check for CAN communication system DTCs (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

HINT:

If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


OK:

No DTC is output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COMBINATION METER)
a.

Disconnect the G59 ECU connector.

A393998E01
5.063,2 5.479,2.25 0.417,0.25 1.667,2.167 2.083,2.417 0.417,0.25 2.073,1.563 2.5,1.417 false 6.052,2.167 6.25,1.635 false 0.469,0.125 2.74,1.156 2.271,1.031 10 false Front view of wire harness connector: (to Main body ECU) 4.094,0.281 6.344,0.969 2.25,0.688 10 false Front view of wire harness connector: (to Combination Meter) 2.563,1.313 3.125,1.563 0.563,0.25 10 false SPD 5.906,2.188 6.469,2.438 0.563,0.25 10 false +S 1.74,2.208 2.302,2.458 0.563,0.25 10 false G59 5.125,2.042 5.688,2.292 0.563,0.25 10 false G28


b.

Disconnect the G28 meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G59-9 (SPD) - G28-40 (+S) Always Below 1 Ω




OK

4.CHECK MAIN BODY ECU (SPEED SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MAIN BODY ECU (SPEED SIGNAL)
a.
U188854E01
0.271,0.066 2.607,0.389 2.336,0.323 10 Front view of wire harness connector: (to Main Body ECU) 2.694,1.884 3.010,2.040 0.316,0.156 10 SPD 2.015,2.133 2.694,1.97 false 0.604,1.816 0.889,1.968 0.285,0.152 10 G59

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G59-9 (SPD) - Body ground Always 10 kΩ or higher


HINT:

If the result of the inspection for a short circuit is not as specified, there may be a short in the ECU.




OK

5.INSPECT MAIN BODY ECU (SPEED SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU

5.INSPECT MAIN BODY ECU (SPEED SIGNAL)
a.
U188846E02
1.885,3.188 2.542,2.635 false 0.323,0.073 2.531,0.417 2.208,0.344 10 false Component with harness connected: (Main Body ECU) 2.552,2.49 2.865,2.646 0.313,0.156 10 false SPD 2.552,3.021 2.948,3.229 0.396,0.208 10 false G59

Check the signal waveform.

i.

Reconnect the connectors.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal G59-9 (SPD) and body ground.


iv.

Turn the engine switch on (IG).


v.

Turn the wheel slowly.


vi.
I042329E26
2.833,1.24 3.208,1.615 0.375,0.375 10 false GND

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 10 ms./DIV.
Vehicle condition Driving at approx. 20 km/h (12mph)

OK:

The waveform is displayed as shown in the illustration.





OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG