ENGINE START SYSTEM OPERATION
When the engine switch is pressed with the brake pedal depressed and shift lever in P or N, the main body ECU determines that it is an engine start request.
The certification ECU and other ECUs perform key verification via the LIN communication line. The engine switch indicator light illuminates in green.
The main body ECU activates the ACC relay.
The main body ECU activates the LH-IG relay 1 and IG2 relays.
The certification ECU outputs a steering UNLOCK signal. The signal is sent to the steering lock ECU via the LIN communication line.
The main body ECU sends an engine start request signal to the ECM.
The ECM sends an ACC cut request signal to the main body ECU.
The ECM and main body ECU activate the ST cut relay.
The main body ECU deactivates the ACC relay until the ECU detects an engine start.
The ECU reactivates the ACC relay and turns off the engine switch indicator light.
| Symbols of main body ECU | Signals |
|---|---|
| SSW1/SSW2 | Engine switch on (ACC, IG) signal |
| ACCD | ACC relay operation signal |
| IG2D | IG2 relay operation signal |
| STR2 | ST cut relay operation signal |
| STR | Park / neutral position switch signal |
| STP | Stop light switch signal |
| TACH | Engine start detection signal |
| STSW | Starter activation request signal |
| ACCR | ACC cut request signal |
Refer to the CRANKING HOLDING FUNCTION CIRCUIT (see page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>Cranking Holding Function Circuit).
Open and close the driver door when the engine switch is off.
Check that the engine starts.
Engine starts.
After the battery runs out, the engine may not start if the steering lock ECU has not been initialized (lock / unlock may not be recorded) through the procedure described above.
NG
OK
Clear the DTCs.
After all DTCs are cleared, check if the trouble occurs again 5 seconds after the engine switch is turned on (IG).
Check for DTCs again.
No DTC is output.
OK
NG
(See pageEngine / Hybrid System>2AZ-FE STARTING>SMART ENTRY AND START SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Ensure the electrical key is inside the cabin.
With the brake pedal released, check that the power source mode changes as shown below each time the engine switch is pushed.
off → on (ACC) → on (IG) → off
OK
NG
Ensure that there is fuel in the fuel tank and the key is inside the cabin.
Depress the brake pedal with the shift lever in P or N, and keep depressing the pedal.
Check that the engine cranks when the engine switch is pressed.
Engine cranks.
NG
OK
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / Main Body ECU / Data List / N SW / C SW.
Read the displays on the tester.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| N SW / C SW | Park / neutral position switch / ON or OFF | ON: Shift lever in P or N
OFF: Shift lever in R or D |
- |
When the shift lever is in P or N, ON is displayed on the tester.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / Main Body ECU / Data List / Stop Light SW2.
Read the displays on the tester.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop Light switch / ON or OFF | ON: Brake pedal is depressed
OFF: Brake pedal is released |
- |
When the brake pedal is depressed, ON is displayed on the tester.
OK
NG
When the engine switch is on (ACC), check that the steering lock can be released.
Steering lock can be released.
OK
NG
Disconnect the G60 main body ECU connector.
Depress the brake pedal with the shift lever in P or N, and keep depressing the pedal.
Measure the voltage of the wire harness side connector when the engine cranks by pressing the engine switch.
| Tester Connection | Specified Condition |
|---|---|
| G60-4 (STSW) - Body ground | 10 to 14 V |
OK
NG
(See pageEngine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Place the electrical key inside the cabin.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / L Code Chk.
Read the display on the tester.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Chk | L Code Check / NG or OK | NG: L code certification result is abnormal
OK: L code certification result is normal |
- |
L code check result is OK.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / S Code Chk.
Read the display on the tester.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| S Code Chk | S Code Check / NG or OK | NG: S code certification result is abnormal
OK: S code certification result is normal |
- |
S code check result is OK.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) (do not start the engine) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / Start Req Sig.
Read the displays on the tester.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Start Rqst | Starter request signal / Yes or No | YES: ID code box receives immobiliser unset signal
NO: ID code box does not receive immobiliser unset signal |
- |
When ID code box receives immobiliser unset signal, YES is displayed on tester.
OK
NG