Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START › from 2016.05
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START J

2AZ-FE STARTING  PUSH-BUTTON START  Engine does not Start  


DESCRIPTION

ENGINE START SYSTEM OPERATION


a.

When the engine switch is pressed with the brake pedal depressed and shift lever in P or N, the main body ECU determines that it is an engine start request.


b.

The certification ECU and other ECUs perform key verification via the LIN communication line. The engine switch indicator light illuminates in green.


c.

The main body ECU activates the ACC relay.


d.

The main body ECU activates the LH-IG relay 1 and IG2 relays.


e.

The certification ECU outputs a steering UNLOCK signal. The signal is sent to the steering lock ECU via the LIN communication line.


f.

The main body ECU sends an engine start request signal to the ECM.


g.

The ECM sends an ACC cut request signal to the main body ECU.


h.

The ECM and main body ECU activate the ST cut relay.


i.

The main body ECU deactivates the ACC relay until the ECU detects an engine start.


j.

The ECU reactivates the ACC relay and turns off the engine switch indicator light.

Symbols of main body ECU Signals
SSW1/SSW2 Engine switch on (ACC, IG) signal
ACCD ACC relay operation signal
IG2D IG2 relay operation signal
STR2 ST cut relay operation signal
STR Park / neutral position switch signal
STP Stop light switch signal
TACH Engine start detection signal
STSW Starter activation request signal
ACCR ACC cut request signal



A135955E03
1.156,5.385 2.5,6.177 1.344,0.792 10 false Park / Neutral Position Switch 5.677,3.604 7.063,3.844 1.385,0.24 10 false Steering Lock ECU 5.76,4.26 7.094,4.5 1.333,0.24 10 false Certification ECU 3.396,0.188 4.458,0.427 1.063,0.24 10 false Main Body ECU 5.813,2.948 6.75,3.167 0.938,0.219 10 false ID Code Box 5.479,2.365 6.813,2.583 1.333,0.219 10 false Combination Meter 0.854,1 1.719,1.208 0.865,0.208 10 false from Battery 0.469,6.177 1.083,6.667 0.615,0.49 10 false from Battery 0.417,7.281 1.281,7.521 0.865,0.24 10 false to Starter 3.146,1.427 3.708,1.656 0.563,0.229 10 false CANH 3.146,1.021 3.646,1.25 0.5,0.229 10 false AM1 3.146,1.177 3.656,1.406 0.51,0.229 10 false AM2 2.115,0.854 3.063,1.083 0.948,0.229 10 false AM2 NO. 2 3.167,6.833 3.729,7.063 0.563,0.229 10 false STA 4.271,5.521 4.729,5.75 0.458,0.229 10 false ACCR 4.281,6.906 4.844,7.135 0.563,0.229 10 false STSW 4.26,4.635 4.823,4.865 0.563,0.229 10 false STSW 3.156,6.458 3.719,6.688 0.563,0.229 10 false STAR 3.135,4.583 3.698,4.813 0.563,0.229 10 false STR 3.156,5.063 3.719,5.292 0.563,0.229 10 false STR2 3.146,5.615 3.708,5.844 0.563,0.229 10 false GND2 4.427,2.417 4.99,2.646 0.563,0.229 10 false SPD 4.271,1.542 4.833,1.771 0.563,0.229 10 false SSW2 4.281,1.323 4.844,1.552 0.563,0.229 10 false SSW1 4.583,0.542 4.729,0.771 0.146,0.229 10 false P 3.135,0.51 3.479,0.74 0.344,0.229 10 false STP 3.156,2.344 3.688,2.604 0.531,0.26 10 false IG1D 2.188,2.615 3.115,2.875 0.927,0.26 10 false LH-IG Relay 1 3.177,3.167 3.708,3.427 0.531,0.26 10 false IG2D 1.76,3.438 2.125,3.698 0.365,0.26 10 false IG2 4.323,6.615 4.938,6.844 0.615,0.229 10 false TACH 4.313,5.094 4.927,5.323 0.615,0.229 10 false TACH 4.302,6.344 4.917,6.594 0.615,0.25 10 false ACCR 3.156,4.01 3.771,4.26 0.615,0.25 10 false ACCD 3.677,6.146 4.208,6.375 0.531,0.229 10 false ECM 5.781,6.573 6.417,6.781 0.635,0.208 10 false CAN 0.969,1.552 2.75,1.76 1.781,0.208 10 false CAN Communication Line 5.792,6.229 6.208,6.438 0.417,0.208 10 false LIN 4.385,2.979 4.802,3.188 0.417,0.208 10 false LIN1 4.906,2.844 5.323,3.052 0.417,0.208 10 false LIN 5.76,5.625 6.688,5.844 0.927,0.219 10 false Electrical Key 1.833,6.771 2.229,6.979 0.396,0.208 10 false ST 1.823,4.26 2.5,4.469 0.677,0.208 10 false ST CUT 1.031,4.281 1.354,4.5 0.323,0.219 10 false ACC 3.26,2.167 3.948,2.396 0.688,0.229 10 false B2272* 3.26,2.979 3.948,3.208 0.688,0.229 10 false B2273* 3.385,5.375 4.073,5.604 0.688,0.229 10 false B2271* 3.365,3.781 4.052,4.01 0.688,0.229 10 false B2274* 4.979,3.135 5.563,3.365 0.583,0.229 10 false B2285* 4.99,3.99 5.552,4.219 0.563,0.229 10 false B2289* 4.99,3.813 5.594,4.042 0.604,0.229 10 false B2287* 4.052,1.167 4.74,1.396 0.688,0.229 10 false B2278* 4.177,0.688 4.865,0.917 0.688,0.229 10 false B2281* 4.01,4.438 4.698,4.667 0.688,0.229 10 false B2275* 4,5.323 4.688,5.552 0.688,0.229 10 false B2276* 3.99,4.917 4.677,5.146 0.688,0.229 10 false B2286* 4.073,2.021 4.76,2.25 0.688,0.229 10 false B2282* 4.073,2.188 4.76,2.417 0.688,0.229 10 false B2283* 3.146,1.688 3.646,1.917 0.5,0.229 10 false CANL 4.979,3.323 5.563,3.552 0.583,0.229 10 false B2288* 3.313,0.813 4,1.042 0.688,0.229 10 false B2271* 3.094,7.344 6.365,7.615 3.271,0.271 10 false *: These DTCs are set when there is a malfunction 5.333,1.813 6.281,2.042 0.948,0.229 10 false Engine Switch 5.49,0.438 6.99,0.802 1.5,0.365 10 false Shift Lock Control ECU 1.292,0.51 2.417,0.875 1.125,0.365 10 false Stop Light Switch

WIRING DIAGRAM

Refer to the CRANKING HOLDING FUNCTION CIRCUIT (see page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>Cranking Holding Function Circuit).

PROCEDURE

1.CHECK WHETHER ENGINE STARTS AFTER STEERING LOCK INITIALIZATION
a.

Open and close the driver door when the engine switch is off.


b.

Check that the engine starts.

OK:

Engine starts.



HINT:

After the battery runs out, the engine may not start if the steering lock ECU has not been initialized (lock / unlock may not be recorded) through the procedure described above.



NG

2.CHECK WHETHER DTC OUTPUT RECURS (MAIN BODY ECU AND CERTIFICATION ECU)

OK

SYSTEM OK

2.CHECK WHETHER DTC OUTPUT RECURS (MAIN BODY ECU AND CERTIFICATION ECU)
a.

Clear the DTCs.

HINT:

After all DTCs are cleared, check if the trouble occurs again 5 seconds after the engine switch is turned on (IG).



b.

Check for DTCs again.

OK:

No DTC is output.




OK

3.CHECK SWITCH CONDITION

NG

3.CHECK SWITCH CONDITION
a.

Ensure the electrical key is inside the cabin.


b.

With the brake pedal released, check that the power source mode changes as shown below each time the engine switch is pushed.

OK:

off → on (ACC) → on (IG) → off




OK

4.CHECK BASIC FUNCTION

NG

4.CHECK BASIC FUNCTION
a.

Ensure that there is fuel in the fuel tank and the key is inside the cabin.


b.

Depress the brake pedal with the shift lever in P or N, and keep depressing the pedal.


c.

Check that the engine cranks when the engine switch is pressed.

OK:

Engine cranks.




NG

5.READ VALUE USING GTS (N SW / C SW)

OK

9.READ VALUE USING GTS (L CODE CHECK)
5.READ VALUE USING GTS (N SW / C SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Main Body ECU / Data List / N SW / C SW.


d.

Read the displays on the tester.

Main body ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Park / neutral position switch / ON or OFF ON: Shift lever in P or N
OFF: Shift lever in R or D
-


OK:

When the shift lever is in P or N, ON is displayed on the tester.




OK

6.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

REPAIR OR REPLACE PARK/NEUTRAL POSITION SWITCH

6.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Main Body ECU / Data List / Stop Light SW2.


d.

Read the displays on the tester.

Main body ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Stop Light SW Stop Light switch / ON or OFF ON: Brake pedal is depressed
OFF: Brake pedal is released
-


OK:

When the brake pedal is depressed, ON is displayed on the tester.




OK

7.CHECK STEERING LOCK SYSTEM

NG

REPAIR OR REPLACE STOP LIGHT SWITCH

7.CHECK STEERING LOCK SYSTEM
a.

When the engine switch is on (ACC), check that the steering lock can be released.

OK:

Steering lock can be released.




OK

8.INSPECT MAIN BODY ECU

NG

8.INSPECT MAIN BODY ECU
a.

Disconnect the G60 main body ECU connector.


b.

Depress the brake pedal with the shift lever in P or N, and keep depressing the pedal.


c.

Measure the voltage of the wire harness side connector when the engine cranks by pressing the engine switch.

Standard voltage:
Tester Connection Specified Condition
G60-4 (STSW) - Body ground 10 to 14 V




OK

REPLACE MAIN BODY ECU

NG

GO TO SFI SYSTEM (CRANKING HOLDING FUNCTION CIRCUIT)

9.READ VALUE USING GTS (L CODE CHECK)
a.

Place the electrical key inside the cabin.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the tester ON.


d.

Select the following menu items: Body Electrical / Certification ECU / Data List / L Code Chk.


e.

Read the display on the tester.

Certification ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
L Code Check L Code Check / NG or OK NG: L code certification result is abnormal
OK: L code certification result is normal
-


OK:

L code check result is OK.




OK

10.READ VALUE USING GTS (S CODE CHECK)

NG

GO TO ENGINE IMMOBILISER SYSTEM (STEERING LOCK ECU OR ID CODE BOX MALFUNCTIONS)

10.READ VALUE USING GTS (S CODE CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Certification ECU / Data List / S Code Chk.


d.

Read the display on the tester.

Certification ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
S Code Check S Code Check / NG or OK NG: S code certification result is abnormal
OK: S code certification result is normal
-


OK:

S code check result is OK.




OK

11.READ VALUE USING GTS (ENGINE START REQUEST)

NG

GO TO ENGINE IMMOBILISER SYSTEM (CERTIFICATION ECU OR ID CODE BOX MALFUNCTIONS)

11.READ VALUE USING GTS (ENGINE START REQUEST)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) (do not start the engine) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Certification ECU / Data List / Start Req Sig.


d.

Read the displays on the tester.

Certification ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Engine Start Request Starter request signal / Yes or No YES: ID code box receives immobiliser unset signal
NO: ID code box does not receive immobiliser unset signal
-


OK:

When ID code box receives immobiliser unset signal, YES is displayed on tester.




OK

REPLACE ID CODE BOX

NG

REPLACE CERTIFICATION ECU