Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START J

2AZ-FE STARTING  PUSH-BUTTON START  Room Oscillator does not Recognize Key  


DESCRIPTION

The certification ECU uses the indoor electrical key antenna to send a request signal to the key when: 1) the driver side door is opened and closed, or 2) the engine switch is turned from on (ACC) to off or off to on (ACC). Then, the key transmits its ID code to the door control receiver. The ID code, which is then sent to the certification ECU, is verified by the certification ECU and the verification result is sent to the ID code box. Turning the engine switch from on (ACC) to off stops the engine control system.

The ID code box and the certification ECU communicate encryption codes to each other using the LIN communication line. When the return code from the certification ECU matches the ID code in the memory, the ID code box sends an engine control system start permission signal to the ECM. With the brake pedal depressed, pressing the engine switch starts the engine. With the engine running, pressing the engine switch stops engine.

WIRING DIAGRAM

B144447E13
0.271,1.792 2.813,1.979 2.542,0.188 10 false Indoor Electrical Key Antenna (for Front) 0.25,3.938 2.896,4.125 2.646,0.188 10 false Indoor Electrical Key Antenna (for Rear 1) 0.25,6.063 2.865,6.271 2.615,0.208 10 false Indoor Electrical Key Antenna (for Rear 2) 5.542,6.021 6.781,6.313 1.24,0.292 10 false Certification ECU 1.542,0.417 1.948,0.594 0.406,0.177 10 false CLG3 2.125,0.635 2.354,0.865 0.229,0.229 10 false 1 1.542,1.031 1.948,1.208 0.406,0.177 10 false CLGB 2.125,1.25 2.354,1.479 0.229,0.229 10 false 3 1.552,2.573 1.958,2.75 0.406,0.177 10 false CLG4 2.115,2.76 2.344,2.99 0.229,0.229 10 false 1 1.552,3.188 1.958,3.365 0.406,0.177 10 false CLGB 2.125,3.406 2.354,3.635 0.229,0.229 10 false 2 1.531,4.688 1.938,4.865 0.406,0.177 10 false CLG6 2.104,4.906 2.333,5.146 0.229,0.24 10 false 1 1.531,5.292 1.938,5.469 0.406,0.177 10 false CLGB 2.125,5.5 2.354,5.729 0.229,0.229 10 false 2 5.646,0.531 6.052,0.708 0.406,0.177 10 false CLG5 5.344,0.625 5.573,0.854 0.229,0.229 10 false 11 5.667,1.156 6.073,1.333 0.406,0.177 10 false CG5B 5.333,1.25 5.563,1.479 0.229,0.229 10 false 12 5.656,2.677 6.063,2.854 0.406,0.177 10 false CLG6 5.313,2.76 5.542,2.99 0.229,0.229 10 false 13 5.667,3.313 6.073,3.49 0.406,0.177 10 false CG6B 5.333,3.396 5.563,3.625 0.229,0.229 10 false 14 5.667,4.781 6.073,4.958 0.406,0.177 10 false CLG7 5.333,4.865 5.563,5.094 0.229,0.229 10 false 15 5.656,5.396 6.063,5.573 0.406,0.177 10 false CG7B 5.344,5.51 5.573,5.74 0.229,0.229 10 false 16 5.531,5.854 5.844,6.01 0.313,0.156 10 false G29 0.25,5.906 0.521,6.094 0.271,0.188 10 false O1 0.25,3.781 0.521,3.969 0.271,0.188 10 false M19 0.26,1.646 0.604,1.823 0.344,0.177 10 false M36

PROCEDURE

1.CHECK KEY CANCEL FUNCTION
a.

Check that the key cancel function has been set (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>CUSTOMIZE PARAMETERS).

OK:

Key cancel function is set.




NG

2.CHECK WIRELESS DOOR LOCK CONTROL OPERATION

OK

END (UNSET KEY CANCEL FUNCTION)

2.CHECK WIRELESS DOOR LOCK CONTROL OPERATION
a.

Check that the wireless door lock and unlock functions operate normally.

OK:

Wireless door lock and unlock functions operate normally.




OK

3.PERFORM ACTIVE TEST USING GTS (INDOOR ELECTRICAL KEY ANTENNA)

NG

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (w/ ENGINE SWITCH)

3.PERFORM ACTIVE TEST USING GTS (INDOOR ELECTRICAL KEY ANTENNA)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the indoor electrical key antenna (front, rear1, rear2) operates.

Certification ECU:
Item Test Details Diagnostic Note
Fr-Seat Inside Transmitter Indoor electrical key antenna (for front) ON / OFF -
Rr-Seat Inside Transmitter Indoor electrical key antenna (for rear1) ON / OFF -
Inside Trunk/Backdoor Transmitter Indoor electrical key antenna (for rear2) ON / OFF -

OK:

When key is brought close to indoor electrical key oscillator, oscillator is turned OFF and indicator on key illuminates.




NG

4.CHECK WIRE HARNESS (INDOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

OK

6.OPERATION CHECK (ENGINE START)
4.CHECK WIRE HARNESS (INDOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the M36, M19 or O1 antenna connectors.


b.

Disconnect the G29 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for Front:
Tester Connection Specified Condition
M36-1 (CLG3) - G29-11 (CLG5) Below 1 Ω
M36-3 (CLGB) - G29-12 (CG5B)
M36-1 (CLG3) or G29-11 (CLG5) - Body ground 10 kΩ or higher
M36-3 (CLGB) or G29-12 (CG5B) - Body ground

for Rear1:
Tester Connection Specified Condition
M19-1 (CLG4) - G29-13 (CLG6) Below 1 Ω
M19-2 (CLGB) - G29-14 (CG6B)
M19-1 (CLG4) or G29-13 (CLG6) - Body ground 10 kΩ or higher
M19-2 (CLGB) or G29-14 (CG6B) - Body ground

for Rear2:
Tester Connection Specified Condition
O1-1 (CLG6) - G29-15 (CLG7) Below 1 Ω
O1-2 (CLGB) - G29-16 (CG7B)
O1-1 (CLG6) or G29-15 (CLG7) - Body ground 10 kΩ or higher
O1-2 (CLGB) or G29-16 (CG7B) - Body ground




OK

5.CHECK INDOOR ELECTRICAL KEY ANTENNA (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INDOOR ELECTRICAL KEY ANTENNA (OPERATION)
a.

Carry the key into the vehicle.


b.

Temporarily replace the indoor electrical key oscillator with a new or normally functioning one.


c.

Depress the brake pedal and check that the engine switch indicator illuminates in green.

OK:

Engine switch indicator illuminates in green.




OK

END (INDOOR ELECTRICAL KEY ANTENNA IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU

6.OPERATION CHECK (ENGINE START)
a.

Remove the key's battery.


b.

While depressing the brake pedal, hold the key near the engine switch. The engine switch's indicator will turn green.


c.

Check that pressing the engine switch starts the engine.



OK

7.OPERATION CHECK (CHECK ENGINE START AGAIN)

NG

GO TO OTHER PROBLEM (Power Source Mode does not Change)

7.OPERATION CHECK (CHECK ENGINE START AGAIN)
a.

Install the key's battery.


b.

Change the vehicle's location or the key's location. For example, place the key in the vehicle interior near the antenna or door control receiver, etc.). Check the engine start operation.



NG

8.CHECK DOOR CONTROL TRANSMITTER (OPERATION)

OK

TROUBLE CAUSED BY ENVIRONMENTAL NOISE

8.CHECK DOOR CONTROL TRANSMITTER (OPERATION)
a.

Temporarily replace the door control transmitter with a new or normally functioning one.


b.

Check that the wireless door lock and unlock functions operate normally.

OK:

Wireless door lock and unlock functions operate normally.




OK

REPLACE CERTIFICATION ECU

NG

END (DOOR CONTROL TRANSMITTER IS DEFECTIVE)