Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0776  Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2)  


SYSTEM DESCRIPTION

The TCM uses the vehicle speed signal to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).

Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect shift solenoid valves and valve body mechanical problems.

DTC No. DTC Detection Condition Trouble Area
P0776 The engine revs freely when 4th, 5th, or 6th gear is requested. (2-trip detection logic)
When any of the following is detected twice (2-trip detection logic):
·

When 1st gear is requested, 4th gear is engaged.

·

When 2nd gear is requested, 4th gear is engaged.

·

When 3rd gear is requested, 4th gear is engaged.


·

Shift solenoid valve SL2 remains open or closed

·

Valve body is blocked

·

Automatic transaxle (clutch, brake or gear etc.)



MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on or off. According to the input shaft revolution, intermediate (counter) shaft revolution and output shaft revolution, the TCM detects the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear position). When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL and stores the DTC.

PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0776)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the intelligent tester on.


c.

Enter the following items: "Powertrain / ECT / DTC / Current or Pending".


d.

Read the DTCs using the intelligent tester.

Result:
Display (DTC output) Proceed to
Only "P0776" is output A
"P0776" and other DTCs are output B


HINT:

If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.




B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

A

3.INSPECT SHIFT SOLENOID VALVE (SL2)
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
NOTICE:

This test should always be performed by at least 2 people.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the intelligent tester on.


c.

Enter the following items: "Powertrain / ECT / Active Test / Control the Shift Position".

HINT:

Comparing the shift position commanded by the Active Test with the actual shift position enables confirmation of the problem (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position [Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
IDL: ON
[Shift Position]
0001: 1st / 0010: 2nd / 0011: 3rd / 0100: 4th / 0101: 5th / 0110: 6th
Possible to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
Do not downshift at high speeds. Doing so will damage the automatic transaxle.


NOTICE:
·

This test can be conducted when the vehicle is stopped.

·

When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.



HINT:

The shift position commanded by the TCM is shown in the "Data List / Shift Status" display on the intelligent tester.



d.

Check the vehicle speed and the gear position when the engine speed is 1,000 rpm.

HINT:

Because the torque converter assembly has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gears, however a difference of speed should still be evident following each gear change.


Standard:
1st 2nd 3rd 4th 5th 6th
8 to 12 km/h (5 to 7.5 mph) 15 to 19 km/h (9.3 to 11.8 mph) 21 to 25 km/h (13.0 to 15.5 mph) 31 to 35 km/h (19.3 to 21.7 mph) 44 to 48 km/h (27.3 to 29.8 mph) 52 to 56 km/h (32.3 to 34.8 mph)



e.

Compare the TCM gear shift command and the actual gear position.

Result:
Actuator gear position under malfunction TCM gear shift command Proceed to
1st 2nd 3rd 4th 5th 6th
Shift solenoid SL1 Stuck ON 1st 2nd 3rd 4th 4th 4th A
Stuck OFF N*1 N*1 N*1 N*1 5th 6th
Shift solenoid SL2 Stuck ON 4th 4th 4th 4th 5th 6th B
Stuck OFF 1st 2nd 3rd 1st N*1 N*1
Shift solenoid SL3 Stuck ON 2nd 2nd 3rd 4th 5th 6th C
Stuck OFF 1st 1st 3rd 4th 5th N*1
Shift solenoid SL4 Stuck ON*3 3rd 3rd 3rd 4th 5th 5th D
Stuck OFF 1st 2nd 1st 4th N*1 6th
Shift solenoid SLT Stuck ON N*2 N*2 N*2 N*2 N*2 N*2 E
Stuck OFF*3 1st 2nd 3rd 4th 5th 6th


HINT:
·

*1: Neutral

·

*2: If the shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.

·

*3: When the shift solenoid SLT is stuck OFF, gear shifting is normal.





B

3.INSPECT SHIFT SOLENOID VALVE (SL2)

A

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL1) PERFORMANCE DTC P0746)

C

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL3) PERFORMANCE DTC P0796)

D

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL4) PERFORMANCE DTC P2808)

E

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SLT) PERFORMANCE DTC P2714)

3.INSPECT SHIFT SOLENOID VALVE (SL2)
a.
G102540E02
1.76,3.115 2.469,2.76 false 1.49,3.115 0.781,2.802 false 1.76,0.906 2.469,0.552 false 1.479,0.896 0.771,0.583 false 0.115,0.063 1.938,0.385 1.823,0.323 10 false Shift Solenoid Valve SL2: 0.625,0.479 0.938,0.677 0.313,0.198 10 false 1 2.542,0.458 2.854,0.656 0.313,0.198 10 false 2 1.198,4.167 1.51,4.365 0.313,0.198 10 false (-) 1.917,4.177 2.229,4.375 0.313,0.198 10 false (+) 0.635,2.698 0.948,2.896 0.313,0.198 10 false 1 2.531,2.656 2.844,2.854 0.313,0.198 10 false 2

Remove the shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
1 - 2 5.0 to 5.6 Ω
(at 20°C (68°F))



c.

Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

OK:

The solenoid makes an operating sound.




OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

REPLACE SHIFT SOLENOID VALVE (SL2)

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:

There are no foreign objects on each valve and the valves operate smoothly.



OK

5.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

5.INSPECT TORQUE CONVERTER ASSEMBLY

OK:

The torque converter assembly operates normally.



OK

REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

REPLACE TORQUE CONVERTER ASSEMBLY