Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM U

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the Data List function of the intelligent tester allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG).


e.

Turn the tester on.


f.

Enter the following menus: "Powertrain / ECT / Data List".


g.

According to the display on the tester, read "Data List".

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Calculate Load Calculated load by ECM/
Min.: 0%, Max.: 100%
·

15.0 to 35.0%: Idling

·

10.0 to 30.0%: Running without load (2,000 rpm)


-
Engine Speed Engine speed:
Min./ 0 rpm, Max.: 16,383.75 rpm
550 to 800 rpm: Idling -
Vehicle Speed Vehicle speed:
Min./ 0 km/h, Max.: 255 km/h
Actual vehicle load -
Coolant Temp Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
80 to 105°C (176 to 221°F): After warming up
·

If value -40°C (-40°F): sensor circuit open

·

If value 140°C (284°F): sensor circuit shorted


Throttle Position Throttle position/
Min.: 0%, Max.: 100%
10 to 22%: Idling Calculated value based on VTA1
Throttle Position from EFI Throttle position/
Min.: 0%, Max.: 100%
·

0%: Accelerator pedal released

·

64 to 96%: Accelerator pedal fully depressed


Recognition valve for throttle opening angle on ECM
SPD (NC) Min.: 0 rpm, Max.: 12,750 rpm - -
SPD (NT) Input turbine speed/
Display: 50 r/min
HINT:
·

Lock-up ON (After warming up the engine):

Input turbine speed (NT) equal to the engine speed.

·

Lock-up OFF (Idling at N position):

Input turbine speed (NT) nearly equal to the engine speed.



-
Closed Throttle Position SW Closed throttle position switch/
ON or OFF
·

ON: Throttle fully closed

·

OFF: Throttle open


-
Starter Signal Starter signal/
ON or OFF
ON: Cranking -
Neutral Position SW Signal PNP switch status/
ON or OFF
Shift lever position is;
P and N: ON
Except P and N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, see page (Click here).


Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF


-
Battery Voltage Battery voltage/
Min.: 0, Max.: 65.535 V
9 to 14 V: Idling -
TC and TE1 TC and CG terminals of DLC3/
ON or OFF
- Active Test support data
Idle Fuel Cut Fuel cut idle/
ON or OFF
ON: Fuel cut operating FC IDL="ON" with the throttle valve fully closed and the engine speed over 2,800 rpm
FC TAU Fuel cut TAU (Fuel cut during very light load)/
ON or OFF
ON: Fuel cut operating Fuel cut being performed under very light load to prevent incomplete engine combustion.
Shift Status ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
Shift lever position is;
D: 1st, 2nd, 3rd, 4th, 5th or 6th
S: 1st, 2nd, 3rd, 4th, 5th or 6th
-
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever position is;
R: ON
Except R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, see page (Click here).


Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever position is;
P: ON
Except P: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, see page (Click here).


Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever position is;
N: ON
Except N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, see page (Click here).


Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever position is;
D and S: ON
Except D and S: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:

When the failure still occurs even after adjusting these parts, see page (Click here).


Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

Press continuously "+" (Up shift): ON

·

Release "+" (Up shift): OFF


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

Press continuously "-" (Down shift): ON

·

Release "-" (Down shift): OFF


-
Sports Mode selection SW Sport mode select switch status/
ON or OFF
Shift lever position is;
S, "+" and "-": ON
Except S, "+" and "-": OFF
-
TPS 1 Switch 0: OFF / 1: ON Gear position 1st, 2nd, 3rd or 4th: ON
Gear position 5th or 6th: OFF
-
TPS 2 Switch 0: OFF / 1: ON Gear position 4th, 5th or 6th: ON
Gear position 1st, 2nd or 3rd: OFF
-
TPS 3 Switch 0: OFF / 1: ON Shift solenoid valve SLU is ON: ON
Shift solenoid valve SLU is OFF: OFF
-
A/T Oil Temperature 1 ATF temp. sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall test;

Approx. 80°C (176°F)

·

Equal to ambient temperature when cold soak


If the value is "-40°C (-40°F)" or "215°C (419°F)", the ATF temp. sensor circuit is open or shorted.
NT Sensor Voltage Min.: 0 V, Max.: 5 V 0.1 to 1.9 V -
NC Sensor Voltage Min.: 0 V, Max.: 5 V 0.1 to 1.9 V -
AT Fluid Flex lockup judder judgement flag /
0: OFF / 1: ON
- -
Lock UP 0: OFF / 1: ON Lock up: ON -
Lock UP Solenoid Status Lock up solenoid status/
ON or OFF
·

Lock up: ON

·

Except lock up: OFF


-
SLU Solenoid Status Shift Solenoid SLU status/
ON or OFF
·

Lock up: ON

·

Except lock up: OFF


-
SLT Solenoid Status Shift solenoid SLT status/
ON or OFF
·

Accelerator pedal is depressed: OFF

·

Accelerator pedal is released: ON


-
Intake-Air Temp from EFI Intake air temperature/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
Equivalent to ambient air temperature
·

If value -40°C (-40°F): sensor circuit open

·

If value 215°C (419°F): sensor circuit shorted


Accel Position from EFI Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal released

·

54 to 86%: Accelerator pedal fully depressed


-
#Codes*1 # of Codes/
Min.: 0, Max.: 255
- Number of detected DTCs
Check Mode*1 Check mode/
0: OFF, 1: ON
ON: Check mode ON -
SPD Test*1 Check mode result for vehicle speed sensor/
0: COMPL, 1: INCMPL
- -
MIL*1 MIL status/
ON or OFF
ON: MIL ON -
MIL On Run Distance*1 MIL ON run distance/
Min.: 0 km,
Max.: 65,535 km
Distance after DTCs are detected -
Running Time from MIL ON*1 Running time from MIL ON/
Min.: 0 minute,
Max.: 65,535 minutes
Equivalent to running time after MIL turns ON -
Engine Run Time Engine run time/
Min.: 0 second,
Max.: 65,535 seconds
Time after engine start -
Time after DTC Cleared Time after DTC cleared/
Min.: 0 minute,
Max.: 65,535 minutes
Equivalent to time after DTCs are erased -
Distance from DTC Cleared Distance after DTC cleared/
Min.: 0 km/h,
Max.: 65,535 km/h
Equivalent to time after DTCs are erased -
Warmup Cycle Cleared Warm-up cycle after DTC cleared/
Min.: 0, Max.: 255
- Number of warm-up cycles after DTCs are cleared
OBD Requirements*1 OBD requirement OBD2 -
Complete Parts Monitor*1 Comprehensive component monitor/
0: NOT AVL / 1: AVAIL
- Comprehensive Component Monitor
Transmission Type*1 Transmission type - Identifying transmission type:
6 speed
SYSTEM System identification - Identifying engine type:
GASOLINE (gasoline engine)



ACTIVE TEST


HINT:

Performing the Active Test using the intelligent tester allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test as the first step in troubleshooting is one method to save diagnostic time.

It is possible to display the Data List during the Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following items: "Powertrain / ECT / Active Test".


g.

According to the display on the tester, perform "Active Test".

Tester Display Test Part Control Range Diagnostic Note
Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
·

ON: TC and TE1 connected


·

OFF: TC and TE1 disconnected


Control the Shift Position [Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
IDL: ON
[Shift Position]
0001: 1st / 0010: 2nd / 0011: 3rd / 0100: 4th / 0101: 5th / 0110: 6th
Possible to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
Do not downshift at high speeds. Doing so will damage the automatic transaxle.
Activate the Lock Up [Test Details]
Control the shift solenoid SLU to set the automatic transaxle to the lock-up condition.
[Vehicle Condition]
·

Throttle valve opening angle: 20% or more

·

Vehicle speed: 70 km/h (43 mph) or more

·

Gear: Highest gear


[Lock-up]
0: OFF / 1: ON
Possible to check the SL solenoid operation.
Activate the Solenoid (SL1) [Test Details]
Operate the shift solenoid SL1
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever in P or N position


[Solenoid (SL1)]
0: OFF / 1: ON
-
Activate the Solenoid (SL2) [Test Details]
Operate the shift solenoid SL2
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever in P or N position


[Solenoid (SL2)]
0: OFF / 1: ON
-
Activate the Solenoid (SL3) [Test Details]
Operate the shift solenoid SL3
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever in P or N position


[Solenoid (SL3)]
0: OFF / 1: ON
-
Activate the Solenoid (SL4) [Test Details]
Operate the shift solenoid SL4
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever in P or N position


[Solenoid (SL4)]
0: OFF / 1: ON
-
Activate the Solenoid (SL) [Test Details]
Operate the shift solenoid SL
[Vehicle Condition]
·

Vehicle stopped

·

Shift lever in P or N position


[Solenoid (SL)]
0: OFF / 1: ON
-
Activate the Solenoid (SLT) [Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]
·

Vehicle stopped

·

IDL: ON


HINT:

OFF: Line pressure up (When the active test of "SOLENOID (SLT)" is performed, the ECM commands the SLT solenoid to turn off).

ON: No action (normal operation)


[Solenoid (SLT)]
0: OFF / 1: ON
-
Activate the Solenoid (SLU)* [Test Details]
Operate the shift solenoid SLU and raise the line pressure.
[Vehicle Condition]
·

Vehicle stopped

·

IDL: ON


HINT:

OFF: Line pressure up (When the active test of "SOLENOID (SLU)" is performed, the ECM commands the SLU solenoid to turn off).

ON: No action (normal operation)


[Solenoid (SLU)]
0: OFF / 1: ON
-

*: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting the SST to the automatic transaxle. The same SST is used for the Hydraulic Test (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST) as well.

HINT:

The pressure values in Active Test and Hydraulic Test will be different from each other.