The TCM uses the vehicle speed signal to determine the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect shift solenoid valves and valve body mechanical problems.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2808 | The engine revs freely when 3rd or 5th gear is requested. (2-trip detection logic)
When any of the following is detected. In addition, the condition that 4th gear is engaged when 4th gear is requested occurs twice. (2-trip detection logic) ·
When 1st gear is requested, 3rd gear is engaged. ·
When 2nd gear is requested, 3rd gear is engaged. ·
When 6th gear is requested, 5th gear is engaged. |
·
Shift solenoid valve SL4 remains open or closed ·
Valve body is blocked ·
Automatic transaxle (clutch, brake or gear etc.) |
The TCM commands gear shifts by turning the shift solenoid valves on or off. According to the input shaft revolution, intermediate (counter) shaft revolution and output shaft revolution, the TCM detects the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear position). When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL and stores the DTC.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
| Display (DTC output) | Proceed to |
|---|---|
| Only "P2808" is output | A |
| "P2808" and other DTCs are output | B |
If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.
B
A
This test should always be performed by at least 2 people.
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / Active Test / Control the Shift Position".
While driving, the shift position can be forcibly changed with the intelligent tester.
Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | [Test Details]
Operate the shift solenoid valve and set each shift position by yourself. [Vehicle Condition] IDL: ON |
[Shift Position]
0001: 1st / 0010: 2nd / 0011: 3rd / 0100: 4th / 0101: 5th / 0110: 6th |
Possible to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. |
This test can be conducted when the vehicle is stopped.
When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.
The shift position commanded by the TCM is shown on the "Data List / Shift Status" display on the intelligent tester.
Check the vehicle speed and the gear position when the engine speed is 1,000 rpm.
Because the torque converter assembly has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gears, however a difference of speed should still be evident following each gear change.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
|---|---|---|---|---|---|
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the TCM gear shift command and the actual gear position.
| Actuator gear position under malfunction | TCM gear shift command | Proceed to | ||||||
|---|---|---|---|---|---|---|---|---|
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid SL4 | Stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
*1: Neutral
*2: If the shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
*3: When the shift solenoid SLT is stuck OFF, gear shifting is normal.
D
A
B
C
E
Remove the shift solenoid valve SL4.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| 1 - 2 | 5.0 to 5.6 Ω
(at 20°C (68°F)) |
Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
The solenoid makes an operating sound.
OK
NG
Check the valve body assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).
There are no foreign objects on each valve and the valves operate smoothly.
OK
NG
Check the torque converter assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).
The torque converter assembly operates normally.
OK
NG