Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL › 2013.04–2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292120 DIFFERENTIAL OIL SEAL A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 2.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C139605

Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the automatic transaxle.


b.
C139606

Remove the refill plug and gasket from the automatic transaxle.


c.
C162901E03
0.615,1.031 0.771,0.125 0.771,0.125 0.896,0.125 true 0.938,0.052 2.927,0.427 1.99,0.375 10 true No. 1 transmission oil filler tube

Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle.


d.

Drain automatic transaxle fluid from the automatic transaxle.


e.
C162901E03
0.615,1.031 0.771,0.125 0.771,0.125 0.896,0.125 true 0.938,0.052 2.927,0.427 1.99,0.375 10 true No. 1 transmission oil filler tube

Install No. 1 transmission oil filler tube to the automatic transaxle.


f.
C139605

Install a new gasket and the overflow plug to the automatic transaxle.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


g.
C139606

Install a new gasket and the refill plug to the automatic transaxle.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 43420 3.REMOVE FRONT DRIVE SHAFT ASSEMBLY

a.

Remove the drive shaft assembly (See page Drivetrain>DRIVE SHAFT>FRONT DRIVE SHAFT ASSEMBLY>REMOVAL).


Hide 31105H 4.REMOVE TRANSAXLE CASE OIL SEAL

a.
C133598E08
1.583,1.552 1.583,1.865 true 1.458,1.875 1.76,2.042 0.302,0.167 10 false SST

Using SST, tap out the transaxle case oil seal.

SST
09308-00010  


Hide 31105D 5.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
C133597E03
1.058,0.194 1.415,0.380 0.357,0.186 10 SST 1.234,0.829 1.234,0.361 false

Using SST, tap out the front transaxle case oil seal.

SST
09308-00010  


Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL

a.
C366259E01
0.969,1.771 1.854,2.76 1.854,2.76 1.219,1.865 true 1.865,2.781 2.323,2.979 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new transaxle case oil seal.

SST
09316-60011  
09950-70010  (09951-07100)

Standard:

-0.5 to 0.5 mm (from the end face of the case)


NOTICE:

Check that the oil seal is installed in the correct direction.



b.

Coat the lip of the transaxle case oil seal with MP grease.


Hide 31105D 7.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C139869E03
0.854,2 1.406,2.75 1.406,2.75 1.51,2.75 true 1.542,2.677 1.875,2.854 0.333,0.177 10 false SST

Using SST and a hammer, tap in a new front transaxle case oil seal.

SST
09316-60011  (09316-00011)

Standard:

-0.5 to 0.5 mm (from the end face of the case)


NOTICE:

Check that the oil seal is installed in the correct direction.



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 43420 8.INSTALL FRONT DRIVE SHAFT ASSEMBLY

a.

Install the drive shaft assembly (See page Drivetrain>DRIVE SHAFT>FRONT DRIVE SHAFT ASSEMBLY>INSTALLATION).


Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 10.ADD AUTOMATIC TRANSAXLE FLUID