Home › Drivetrain › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM24M0E _52 Drivetrain _059580 DRIVE SHAFT _0292135 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 53702 2.REMOVE FRONT FENDER APRON LH

Hide 3.DRAIN AUTOMATIC TRANSAXLE FLUID (for 2AZ-FE, Automatic Transaxle)

Hide 5.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 43502H 6.REMOVE FRONT AXLE HUB NUT

Hide 89542 8.REMOVE FRONT SPEED SENSOR RH

HINT:

Use the same procedures described for the LH side.


Hide 47750 9.REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.
C162626

Remove the 2 bolts and caliper.


Hide 47730 10.REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 48810 11.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 12.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 48069 13.SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH

Hide 48068 14.SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 15.SEPARATE STEERING KNUCKLE WITH AXLE HUB LH

C364222E01
1.625,1.021 2.552,0.688 2.552,0.688 1.698,1.208 false 2.583,0.604 3.292,0.854 0.708,0.25 10 false Matchmark

a.

Put matchmarks on the drive shaft and axle hub.

NOTICE:

Do not punch the marks.



b.

Using a plastic-faced hammer, disconnect the steering knuckle with axle hub.

NOTICE:
·

Be careful not to damage the boot and speed sensor rotor.

·

Do not excessively push out the drive shaft from the axle.




Hide 16.SEPARATE STEERING KNUCKLE WITH AXLE HUB RH

HINT:

Use the same procedures described for the LH side.


Hide 45046 17.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 45046 18.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 43420 19.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C127631E01
2.57,1.863 2.873,2.013 0.304,0.150 10 SST 2.669,1.312 2.811,1.828 false 0.711,1.615 1.288,1.879 false 1.336,1.81 1.639,1.960 0.304,0.150 10 SST

Using SST, remove the front drive shaft.

SST
09520-01010  
09520-24010  (09520-32040)

NOTICE:
·

Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.

·

Be careful not to drop the drive shaft.




Hide 43410 20.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.
C127638

Remove the 2 bolts and pull out the drive shaft together with the drive shaft bearing case.


b.

Remove the drive shaft from the transaxle.

NOTICE:
·

Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.

·

Be careful not to drop the drive shaft.




Hide 21.FIX FRONT AXLE ASSEMBLY

C129482E01
2.792,1.015 3.101,1.172 0.308,0.157 10 SST 2.771,1.098 2.242,1.098 false

NOTICE:

The hub bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore, if it is absolutely necessary to place the vehicle weight on the hub bearing, first support it with SST.


SST
09608-16042  (09608-02021, 09608-02041)