Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › FRONT SPEED SENSOR › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292153 FRONT SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  FRONT SPEED SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 89543 1.INSTALL FRONT SPEED SENSOR LH

NOTICE:

To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.


a.
C130708

Set the sensor body to the knuckle, and then install the sensor with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Keep the sensor tip and sensor installation hole free from foreign matter.

·

Firmly insert the sensor body into the knuckle before tightening the bolt.

·

After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.

·

To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.




b.

Install the sensor clamp and sensor clip as follows.

C367536E01
2.385,0.448 2.688,0.448 2.688,0.448 4.156,1.604 false 2.063,1 2.344,1 2.344,1 3.49,1.469 false 2.833,3.469 3.229,3.875 3.229,3.875 3.448,3.875 false 5.875,0.927 6.188,1.125 0.313,0.198 10 false A 6.458,2.156 6.771,2.354 0.313,0.198 10 false E 5.698,2.667 6.01,2.865 0.313,0.198 10 false B 4.24,3.229 4.552,3.427 0.313,0.198 10 false F 3.969,0.771 4.281,0.969 0.313,0.198 10 false C 3.583,1.958 3.729,2.125 0.146,0.167 10 true D 1,0.344 2.625,0.594 1.625,0.25 10 false Flexible Hose Clamp 0.573,0.906 2.292,1.104 1.719,0.198 10 false Flexible Hose Bracket 3.521,3.781 4.865,4.021 1.344,0.24 10 false Painted Line

i.

Set the flexible hose clamp on the flexible hose bracket.


ii.

Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled A) on the flexible hose bracket (labeled C); and 2) insert the hook part of the sensor clamp (labeled B) into the flexible hose bracket (labeled D).

NOTICE:

Do not twist the sensor wire when installing the clamp.



iii.

Tighten together the sensor clamp, flexible hose clamp and flexible hose bracket with the bolt (labeled E).

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


iv.

Insert the sensor clip (labeled F) into the hole on the absorber lower bracket.



c.
C130706E04
0.896,1.219 1.146,1.219 false 1.146,1.219 0.917,1.625 false 0.115,1.135 0.927,1.5 0.813,0.365 10 true Painted Line 0.469,2.625 0.635,2.792 0.167,0.167 10 false G 0.24,3.49 0.406,3.656 0.167,0.167 10 true H 2.219,1.333 2.385,1.5 0.167,0.167 10 true I

Install the sensor clamp, and sensor clip as follows.

i.

Set the sensor clamp (labeled G) on the side member, and then tighten it with the bolt (labeled H).

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the sensor wire when installing the clamp.



ii.

Insert the sensor clip (labeled I) into the hole on the apron.



d.
C130705E02
1.572,1.434 1.780,1.628 0.208,0.194 10 K 2.865,2.922 3.073,3.116 0.208,0.194 10 J

Insert the sensor clip (labeled J) into the hole on the apron.


e.

Connect the sensor connector (labeled K).


Hide 53876A 2.INSTALL FRONT FENDER LINER LH

Hide 3.INSTALL FRONT WHEEL

T = 103 N*m{ 1,050 kgf*cm 76 ft.*lbf }

Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.CHECK SPEED SENSOR SIGNAL