Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.04–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292157 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1249/49  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU detects the brake operating conditions through a signal transmitted by the stop light switch. The skid control ECU incorporates an open circuit detection circuit. This DTC is set under either of the following conditions:

·

An open is detected in the stop light signal input line when the stop light switch is off.

·

An open is detected in the stop light circuit lead to the ground when the stop light switch is off.


DTC No. DTC Detection Condition Trouble Area
C1249/49 When IG1 terminal voltage is 9.5 to 17.2 V, open circuit of stop light switch continues for 0.5 seconds or more.
·

STOP fuse

·

Stop light switch

·

Stop light switch circuit

·

Brake actuator (Skid control ECU)



WIRING DIAGRAM

C143604E03
0.823,3.052 1.156,3.229 0.333,0.177 10 false ALT 0.802,1.583 1.26,1.76 0.458,0.177 10 false STOP 1.188,0.781 2.375,1.177 1.188,0.396 10 false A1 2.729,1.646 4.74,1.865 2.01,0.219 10 false to Rear Combination Light (LH) 2.729,1.948 4.781,2.167 2.052,0.219 10 false to Rear Combination Light (RH) 2.729,2.26 4.083,2.417 1.354,0.156 10 false to Center Stop Light 5.844,0.479 6.302,0.656 0.458,0.177 10 false STP 5.656,4.073 6.792,4.469 1.135,0.396 10 false A22 0.833,3.906 1.49,4.083 0.656,0.177 10 false FL MAIN 0.833,2.26 1.833,2.438 1,0.177 10 false RH-MAIN-JB 5.563,0.385 5.76,0.552 0.198,0.167 10 false 20 2.115,0.385 2.313,0.552 0.198,0.167 10 false 1 1.313,0.385 1.51,0.552 0.198,0.167 10 false 2 0.896,4.604 1.552,4.781 0.656,0.177 10 false Battery 5.667,4.26 6.802,4.656 1.135,0.396 10 false Skid Control ECU 1.188,0.938 2.375,1.333 1.188,0.396 10 false Stop Light Switch

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Check the Data List for proper functioning of the stop light switch.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Conditions Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

OK:

ON (brake pedal is depressed) appears on the screen.


Result:
Result Proceed to
NG A
OK B




A

2.INSPECT FUSE (STOP)

B

2.INSPECT FUSE (STOP)
a.

Remove the STOP fuse from the instrument panel junction block RH.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPLACE FUSE

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C108891E14
1.219,1.229 1.021,1.042 1.021,1.042 0.833,0.875 false 1.604,2.927 1.167,3.083 false 1.885,2.927 2.198,3.115 false 1.302,1.365 1.354,1.917 false 1.833,2.781 2.167,2.521 false 1.604,2.781 1.083,2.427 false 0.563,0.74 0.854,0.938 0.292,0.198 10 false Pin 0.104,1.906 1.01,2.104 0.906,0.198 10 false Not Pushed 1.583,1.906 2.49,2.104 0.906,0.198 10 false Pushed 0.938,2.281 1.24,2.479 0.302,0.198 10 false 2 2.219,2.354 2.573,2.583 0.354,0.229 10 false 1 2.229,3.052 2.583,3.281 0.354,0.229 10 false 3 0.979,3.031 1.281,3.229 0.302,0.198 10 false 4

Disconnect the stop light switch connector.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
1 - 2 Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher
3 - 4 Pin pushed Below 1 Ω




OK

4.CHECK WIRE HARNESS (SKID CONTROL ECU AND BATTERY - STOP LIGHT SWITCH)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK WIRE HARNESS (SKID CONTROL ECU AND BATTERY - STOP LIGHT SWITCH)
a.
U189312E02
2.031,1.708 2.635,2.417 false 0.167,0.063 1.531,0.25 1.365,0.188 10 false Wire Harness Side: 1.021,0.521 2.156,0.688 1.135,0.167 10 false Skid Control ECU 2.583,2.448 2.958,2.615 0.375,0.167 10 false STP 0.177,0.74 0.469,0.927 0.292,0.188 10 false A22 0.635,3.615 0.927,3.802 0.292,0.188 10 false A1 1.219,2.771 2.438,2.979 1.219,0.208 10 false Stop Light Switch

Disconnect the A22 ECU connector.


b.

Disconnect the A1 switch connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
A22-20 (STP) - A1-1 Below 1 Ω
A22-20 (STP) - Body ground 10 kΩ or higher



d.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
A1-2 - Body ground 10 to 14 V




OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Check if the same DTC is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B