Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.04–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292157 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241/41  Low Battery Positive Voltage  


DESCRIPTION

When there is an abnormality in the power supply circuit of the brake actuator (skid control ECU), the skid control ECU sets a DTC and the operation is prohibited by the fail-safe function. This DTC is set when the voltage supplied to terminal IG1 is outside the DTC detection threshold, due to abnormalities of the battery, power source circuits or charging circuits, such as the alternator circuit.

The fail-safe function is canceled when the voltage to terminal IG1 returns to normal.

DTC No. DTC Detection Condition Trouble Area
C1241/41 With vehicle speed to about 6 km/h (4 mph), battery voltage is less than 9.4 V at the time of non-operation of ABS control or less than 9.2 V at the time of operation of ABS control, or battery voltage is more than 16.9 V.
·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU



WIRING DIAGRAM

C137933E08
5.906,0.75 6.219,0.917 0.313,0.167 10 false IG1 5.771,6.542 6.083,6.698 0.313,0.156 10 false A22 3.063,0.906 4.115,1.073 1.052,0.167 10 false GAUGE NO. 1 0.958,2.74 2,2.927 1.042,0.188 10 false LH-IG Relay 2 3.063,1.521 3.396,1.688 0.333,0.167 10 false ALT 2.615,2.292 3.021,2.458 0.406,0.167 10 false IG1D 3.177,2.625 3.635,2.813 0.458,0.188 10 false AM1 3.167,3.333 3.656,3.521 0.49,0.188 10 false AM2 3.938,3.479 4.719,3.635 0.781,0.156 10 false AM2 NO. 2 4.5,3.146 5.188,3.302 0.688,0.156 10 false F/B BATT 1.146,4.531 1.771,4.729 0.625,0.198 10 false FL MAIN 1.167,6.688 1.792,6.885 0.625,0.198 10 false Battery 5.875,4.969 6.354,5.156 0.479,0.188 10 false GND1 5.875,6.031 6.427,6.229 0.552,0.198 10 false GND2 2.542,3.719 3.625,3.917 1.083,0.198 10 false Main Body ECU 1.854,1.531 2.719,1.698 0.865,0.167 10 false LH-MAIN-JB 2.24,2.302 2.542,2.49 0.302,0.188 10 false G57 3.531,2.635 3.833,2.823 0.302,0.188 10 false G57 3.542,3.323 3.844,3.51 0.302,0.188 10 false G58 3.635,2.417 3.802,2.563 0.167,0.146 10 false 6 5.583,0.604 5.781,0.75 0.198,0.146 10 false 18 2.333,2.094 2.5,2.24 0.167,0.146 10 false 3 3.635,3.115 3.802,3.26 0.167,0.146 10 false 1 5.656,5.875 5.823,6.021 0.167,0.146 10 false 1 5.656,4.833 5.823,4.979 0.167,0.146 10 false 4 5.771,6.708 6.917,6.906 1.146,0.198 10 false Skid Control ECU

PROCEDURE

1.INSPECT FUSE (GAUGE NO. 1)
a.

Remove the GAUGE NO. 1 fuse from the instrument panel junction block LH.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

2.INSPECT BATTERY

NG

REPLACE FUSE

2.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V




OK

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY)

NG

CHECK CHARGING SYSTEM

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY)
a.
U189308E02
1.844,1.854 2.271,2.646 false 0.188,0.094 1.615,0.292 1.427,0.198 10 false Wire Harness Side: 1.5,0.729 1.823,0.885 0.323,0.156 10 false A22 2.219,2.688 2.542,2.865 0.323,0.177 10 false IG1

Disconnect the A22 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
A22-18 (IG1) - Body ground Engine switch on (IG) 10 to 14 V




OK

4.CHECK WIRE HARNESS (SKID CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SKID CONTROL ECU - BODY GROUND)
a.
U189309E02
1.365,1.792 1.75,2.604 false 0.823,1.802 0.833,2.615 false 0.177,0.073 1.604,0.271 1.427,0.198 10 false Wire Harness Side: 1.51,0.74 1.833,0.896 0.323,0.156 10 false A22 0.698,2.656 1.219,2.833 0.521,0.177 10 false GND2 1.667,2.635 2.188,2.813 0.521,0.177 10 false GND1

Disconnect the A22 ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A22-4 (GND1) - Body ground Below 1 Ω
A22-1 (GND2) - Body ground Below 1 Ω




OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Drive the vehicle at 15 km/h (9 mph) or more for several seconds.


c.

Check if the same DTC is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B