Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1234/34  Yaw Rate Sensor Malfunction  C0365/28  Malfunction in Deceleration Sensor  C1245/32  Acceleration Sensor Output Malfunction  


DESCRIPTION

The skid control ECU receives signals from the yaw rate sensor via the CAN communication system.

The yaw rate sensor has a built-in deceleration sensor.

If there is trouble in the bus lines between the yaw rate sensor and the CAN communication system, DTC U0123/62 (Lost Communication with Yaw Rate Sensor Module) is output.

These DTCs are also output when the calibration has not been completed.

DTC No. DTC Detection Condition Trouble Area
C1234/34 Sensor malfunction signal received from yaw rate sensor.
·

Yaw rate sensor

·

Yaw rate sensor circuit


C0365/28 Sensor malfunction signal received from lateral deceleration sensor.
·

Yaw rate sensor

·

Yaw rate sensor circuit


C1245/32 Any of the following is detected:
1.

Longitudinal acceleration difference between sensor signal and reference value is large.

2.

Offset value of sensor signal is higher than the standard value.

3.

Sensor signal is out of range (10 m/s2 continues for 20 seconds).


·

Sensor installation

·

Yaw rate sensor



WIRING DIAGRAM

C137956E06
4.112,0.495 4.370,0.675 0.258,0.179 10 A9 5.438,0.967 5.875,1.123 0.437,0.156 10 CANH 5.438,1.931 5.875,2.087 0.437,0.156 10 CANH 6.297,0.967 6.734,1.123 0.437,0.156 10 CANL 6.297,1.939 6.734,2.095 0.437,0.156 10 CANL 5.339,2.352 5.649,2.508 0.309,0.156 10 IGA 3.616,3.283 4.152,3.620 0.536,0.338 10 RH-IG Relay 1 2.636,2.989 2.996,3.145 0.359,0.156 10 IG1D 1.009,3.143 1.447,3.515 0.439,0.371 10 AM2 NO. 2 2.01,3.397 2.365,3.553 0.355,0.156 10 AM2 2.01,2.977 2.365,3.133 0.355,0.156 10 AM1 1.605,2.518 1.965,2.674 0.360,0.156 10 ALT 0.382,4.15 1.019,4.306 0.637,0.156 10 FL MAIN 0.559,4.823 1.197,4.979 0.637,0.156 10 Battery 5.344,4.324 5.848,4.480 0.505,0.156 10 GNDA 5.608,4.719 5.938,4.887 0.331,0.168 10 N21 4.353,2.53 5.104,2.723 0.751,0.193 10 RH ECU-IG 1.994,3.794 3.038,3.977 1.045,0.184 10 Main Body ECU 5.48,1.238 5.710,1.403 0.230,0.165 10 35 5.555,1.677 5.701,1.879 0.147,0.202 10 2 3.119,2.798 3.266,2.956 0.147,0.157 10 3 5.137,2.247 5.283,2.449 0.147,0.202 10 1 6.563,1.677 6.710,1.879 0.147,0.202 10 3 6.535,1.257 6.719,1.441 0.184,0.184 10 14 5.134,4.207 5.260,4.400 0.126,0.193 10 4 2.359,2.518 3.191,2.702 0.832,0.184 10 RH-MAIN-JB 3.028,2.982 3.323,3.138 0.295,0.155 10 G57 1.675,2.981 1.970,3.165 0.295,0.184 10 G57 1.688,3.403 1.983,3.586 0.295,0.184 10 G58 1.776,3.242 1.880,3.381 0.105,0.139 10 1 1.77,2.807 1.893,2.996 0.123,0.188 10 6 0.518,3.143 0.919,3.483 0.401,0.339 10 F/B BATT 4.112,0.64 5.259,0.824 1.147,0.184 10 Skid Control ECU 5.608,4.873 6.772,5.032 1.164,0.159 10 Yaw Rate Sensor

CAUTION / NOTICE / HINT

HINT:
·

When DTC U0123/62 or U0126/63 is output together with DTC C0365/28, C1234/34 or C1245/32 inspect and repair the trouble areas indicated by DTC U0123/62 or U0126/63 first.

·

When replacing the yaw rate sensor, perform yaw rate sensor zero point calibration first, and then CVT oil pressure calibration (See page Drivetrain>K112 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK DTC

b.

Turn the engine switch off.


c.

Turn the engine switch on (IG) again and check that no CAN communication system DTC(s) is output.


d.

Drive the vehicle at a speed of 30 km/h (19 mph) or more and check that no DTCs are output.

Result
Result Proceed to
DTC is output (relating to yaw rate sensor) A
DTC is output (relating to CAN communication system) B
DTC is not output C



A

2.CHECK YAW RATE SENSOR INSTALLATION

B

C

2.CHECK YAW RATE SENSOR INSTALLATION
a.

Check that the yaw rate sensor has been installed correctly (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

3.CHECK WIRE HARNESS (YAW RATE SENSOR - BATTERY AND BODY GROUND)

NG

3.CHECK WIRE HARNESS (YAW RATE SENSOR - BATTERY AND BODY GROUND)
a.

Disconnect the N21 sensor connector.


U189506E01
0.107,0.145 1.256,0.311 1.149,0.166 10 Yaw Rate Sensor 0.107,0.446 2.492,0.612 2.385,0.166 10 (Harness Side Connector Front View): 0.466,1.587 0.755,1.729 0.289,0.142 10 N21 2.344,1.267 2.653,1.409 0.309,0.142 10 IGA 2.11,2.087 2.44,1.446 false 0.587,3.06 1.041,3.202 0.454,0.142 10 GNDA 0.902,3.026 1.233,2.385 false

b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
N21-1 (IGA) - Body ground Engine switch on (IG) 10 to 14 V



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
N21-4 (GNDA) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR