Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1267/67  Brake Pedal Load Sensing Switch  


DESCRIPTION

The brake pedal load sensing switch sends a signal when the brake pedal is depressed with force exceeding a predetermined level.

The skid control ECU detects if the brake pedal is depressed or not via this circuit.

DTC No. DTC Detection Condition Trouble Area
C1267/67 When one of following conditions is met:
1.

An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.

2.

Immediately after the engine switch is turned on (IG), the brake pedal load sensing switch is ON and the stop light switch is OFF for 10 seconds or more.

3.

While the vehicle speed change from 0 mph (0 km/h) to 18 mph (30 km/h), the condition that the brake pedal load sensing switch remains ON occurs 5 times in succession.

4.

With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 MPa or more, the deceleration is 0.4 G or more for 1 second or more.

5.

With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 MPa or more, the vehicle speed is 0 mph (0 km/h) for 5 seconds or more.


·

Brake pedal load sensing switch

·

Brake pedal load sensing switch circuit



WIRING DIAGRAM

C126312E04
5.531,3.479 6.688,3.635 1.156,0.156 10 false Skid Control ECU 2.313,2.792 4.469,2.979 2.156,0.188 10 false Brake Pedal Load Sensing Switch 5.844,1.823 6.292,1.979 0.448,0.156 10 false FSW+ 2.313,2.615 2.604,2.781 0.292,0.167 10 false A24 2.208,1.938 2.354,2.115 0.146,0.177 10 false 1 4.135,1.948 4.281,2.125 0.146,0.177 10 false 2 5.552,1.927 5.75,2.104 0.198,0.177 10 false 20 5.531,3.323 5.802,3.521 0.271,0.198 10 false A9

CAUTION / NOTICE / HINT

HINT:

If C1249/49 is output, repair it before repairing C1267/67 based on the flow chart below.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL LOAD SENSING SWITCH)
a.

Check the Data List for proper functioning of the brake pedal load sensing switch.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-

OK:

ON (brake pedal is depressed) appears on the screen.




NG

2.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

OK

4.RECONFIRM DTC
2.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
C137922E02
2.083,3.104 2.375,3.344 false 2.563,1.083 2.281,0.74 2.281,0.74 2.208,0.74 false 0.052,0.646 2.271,0.865 2.219,0.219 10 false Brake Pedal Load Sensing Switch 0.083,0.042 0.729,0.25 0.646,0.208 10 false for LHD: 2.406,3.281 3.813,3.5 1.406,0.219 10 false Brake Pedal Support 4.531,1.875 6.51,2.083 1.979,0.208 10 false Brake Pedal Depressed (OFF) 4.542,0.469 6.458,0.667 1.917,0.198 10 false Brake Pedal Released (ON) 4.615,1.365 4.76,1.552 0.146,0.188 10 false 2 6.104,1.354 6.25,1.563 0.146,0.208 10 false 1

C137923E02
2.156,3.083 2.438,3.26 false 2.625,1.052 2.292,0.563 2.292,0.563 2.219,0.563 false 0.094,0.042 0.719,0.229 0.625,0.188 10 false for RHD: 0.073,0.479 2.198,0.646 2.125,0.167 10 false Brake Pedal Load Sensing Switch 2.469,3.229 3.771,3.396 1.302,0.167 10 false Brake Pedal Support 4.531,1.875 6.521,2.083 1.99,0.208 10 false Brake Pedal Depressed (OFF) 4.542,0.51 6.385,0.688 1.844,0.177 10 false Brake Pedal Released (ON) 4.583,1.177 4.719,1.365 0.135,0.188 10 false 2 6.104,1.198 6.271,1.406 0.167,0.208 10 false 1

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal.



a.

Turn the engine switch off.


b.

Disconnect the brake pedal load sensing switch connector.


c.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Condition Specified Condition
2 - 1 Brake pedal depressed (OFF) 0.95 to 1.05 kΩ
2 - 1 Brake pedal released (ON) 202.4 to 223.7 Ω




OK

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
a.
U189322E02
2.594,1.719 2.219,2.323 false 0.052,0.063 1.365,0.229 1.313,0.167 10 false Wire Harness Side: 0.323,0.802 0.563,0.979 0.24,0.177 10 false A9 0.333,3.125 0.615,3.302 0.281,0.177 10 false A24 2,2.344 2.427,2.521 0.427,0.177 10 false FSW+ 0.771,2.823 2.927,3.01 2.156,0.188 10 false Brake Pedal Load Sensing Switch 1.146,0.615 2.281,0.792 1.135,0.177 10 false Skid Control ECU

Disconnect the A9 ECU connector.


b.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
A9-20 (FSW+) - A24-2 Below 1 Ω
A9-20 (FSW+) - Body ground 10 kΩ or higher
A24-1 - Body ground Below 1 Ω




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Check if the same DTC is recorded (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC (C1267/67) is not output A
DTC (C1267/67) is output (for 2AZ-FE) B
DTC (C1267/67) is output (for 2GR-FE) C



A

USE SIMULATION METHOD TO CHECK

B

C

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY