Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1300/62  Skid Control ECU Malfunction  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
C1300/62 Skid control ECU malfunction
·

Wire harness

·

Skid control ECU



WIRING DIAGRAM

C140630E01
4.979,2.363 6.143,2.545 1.164,0.182 10 Skid Control ECU 4.961,1.788 5.438,1.944 0.477,0.156 10 GND2 4.961,1.395 5.438,1.551 0.477,0.156 10 GND1 4.961,0.704 5.438,0.860 0.477,0.156 10 IG1 4.645,0.598 4.844,0.754 0.199,0.156 10 28 4.979,2.209 5.198,2.365 0.219,0.156 10 A9 4.701,1.285 4.831,1.441 0.130,0.156 10 4 4.701,1.677 4.817,1.833 0.116,0.156 10 1 2.936,0.55 3.934,0.706 0.998,0.156 10 GAUGE NO. 1 0.919,0.704 2.007,0.860 1.088,0.156 10 to LH-IG Relay 2

PROCEDURE

1.CHECK DTC

b.

Check if the same DTC is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

2.INSPECT FUSE (GAUGE NO. 1)

B

END

2.INSPECT FUSE (GAUGE NO. 1)
a.

Remove the GAUGE NO. 1 fuse from the instrument panel junction block.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY)

NG

REPLACE FUSE

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY)
a.
U189323E03
1.573,1.792 1.698,2.313 false 0.135,0.25 1.427,0.396 1.292,0.146 10 false Wire Harness Side: 0.469,0.885 0.667,1.031 0.198,0.146 10 false A9 1.604,2.333 1.865,2.5 0.26,0.167 10 false IG1

Disconnect the A9 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
A9-28 (IG1) - Body ground Engine switch on (IG) 10 to 14 V




OK

4.CHECK WIRE HARNESS (SKID CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SKID CONTROL ECU - BODY GROUND)
a.
U189324E03
1.188,1.76 1.313,2.281 false 0.74,1.76 0.604,2.24 false 0.135,0.25 1.427,0.396 1.292,0.146 10 false Wire Harness Side: 0.469,0.875 0.667,1.021 0.198,0.146 10 false A9 1.167,2.281 1.594,2.448 0.427,0.167 10 false GND1 0.354,2.292 0.781,2.458 0.427,0.167 10 false GND2

Disconnect the A9 ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A9-4 (GND1) - Body ground Below 1 Ω
A9-1 (GND2) - Body ground Below 1 Ω




OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Drive the vehicle at 40 km/h (25 mph) or more for several seconds.


c.

Check if the same DTC is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for 2AZ-FE) B
DTC is output (for 2GR-FE) C



A

END

B

C

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY