Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380/64  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop light comes on.

DTC No. DTC Detection Condition Trouble Area
C1380/64 Either of the following is detected:
1.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay drive output (STP0) is ON, a signal has not been input to the STP terminal for 2 seconds or more.

2.

When the voltage at the IG1 terminal is between 10 and 14 V and the stop light control relay drive output (STP0) is OFF, the signal at the STP is different from the input signal at the STP2 for 5 seconds or more.


·

Stop light switch

·

Stop light switch circuit

·

Stop light control (BRK-LP) relay

·

Stop light control (BRK-LP) relay circuit

·

ABS and TRACTION actuator (Skid control ECU)



CAUTION / NOTICE / HINT

HINT:

When DTC C1249/49 is output together with DTC C1380/64, inspect and repair the trouble areas indicated by DTC C1249/49 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249/49).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL (BRK-LP) RELAY)

NG

9.INSPECT SKID CONTROL ECU (STP TERMINAL)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL (BRK-LP) RELAY)
a.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light control (BRK-LP) relay Relay ON/OFF Stop lights come on


b.

Check that the "ON" and "OFF" of the stop lights can be shown on the rear combination light by the intelligent tester.

OK:

The stop lights turn on or off in accordance with the intelligent tester.




OK

4.INSPECT SKID CONTROL ECU (STP2 TERMINAL)

NG

6.INSPECT STOP LIGHT CONTROL (BRK-LP) RELAY
4.INSPECT SKID CONTROL ECU (STP2 TERMINAL)
a.
U189327E02
2.021,1.719 2.302,2.292 false 0.135,0.25 2.385,0.667 2.25,0.417 10 false Front view of wire harness connector: (to Skid Control ECU) 0.448,0.885 0.646,1.031 0.198,0.146 10 false A9 2.146,2.313 2.552,2.479 0.406,0.167 10 false STP2

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A9-13 (STP2) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
A9-13 (STP2) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V




OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
DTC is output (for 2AZ-FE) B
DTC is output (for 2GR-FE) C




A

B

C

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

6.INSPECT STOP LIGHT CONTROL (BRK-LP) RELAY
a.
C366275E01
2.5,1.563 2.24,1.104 false 2.74,1.938 3.073,1.094 false 2.083,2.938 2.24,2.469 false 2.604,2.99 2.604,2.469 false 3.115,2.969 2.948,2.448 false 0.125,0.094 2.583,0.49 2.458,0.396 10 false Stop Light Control (BRK-LP) Relay: 2.146,0.927 2.469,1.188 0.323,0.26 10 false 3 3.052,0.906 3.26,1.135 0.208,0.229 10 false 5 2.031,2.969 2.354,3.229 0.323,0.26 10 false 2 2.563,3 2.885,3.26 0.323,0.26 10 false 4 3.115,3.021 3.323,3.24 0.208,0.219 10 false 1

Turn the engine switch off.


b.

Remove the stop light control (BRK-LP) relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 4 Voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω




OK

7.INSPECT ENGINE ROOM NO. 1 RELAY BLOCK (POWER SOURCE TERMINAL)

NG

REPLACE STOP LIGHT CONTROL (BRK-LP) RELAY

7.INSPECT ENGINE ROOM NO. 1 RELAY BLOCK (POWER SOURCE TERMINAL)
a.
C205479E01
0.132,0.01 2.233,0.187 2.100,0.177 10 Engine Room No. 1 Relay Block: 1.965,2.198 3.137,2.534 1.172,0.336 10 Stop Light Control (BRK-LP) Relay

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Stop light control (BRK-LP) relay terminal 5 - Body ground Always 11 to 14 V
Stop light control (BRK-LP) relay terminal 2 - Body ground Engine switch on (IG) 11 to 14 V




OK

8.INSPECT SKID CONTROL ECU (STP0 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

8.INSPECT SKID CONTROL ECU (STP0 TERMINAL)
a.
U189328E02
2.469,1.802 2.271,2.354 false 0.135,0.25 2.396,0.708 2.26,0.458 10 false Front view of wire harness connector: (to Skid Control ECU) 0.438,0.885 0.635,1.031 0.198,0.146 10 false A9 2.073,2.375 2.5,2.542 0.427,0.167 10 false STP0

Install the stop light control (BRK-LP) relay.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Turn the engine switch on (IG).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A9-39 (STP0) - Body ground Engine switch on (IG) 11 to 14 V


Result:
Result Proceed to
OK (for 2AZ-FE) A
OK (for 2GR-FE) B
NG C




A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP0 CIRCUIT)

9.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.
U189329E02
1.74,1.792 1.865,2.313 false 0.135,0.25 2.75,0.396 2.615,0.146 10 false Front view of wire harness connector: 0.469,0.865 0.667,1.01 0.198,0.146 10 false A9 1.708,2.313 2.135,2.479 0.427,0.167 10 false STP 0.135,0.438 1.521,0.583 1.385,0.146 10 false (to Skid Control ECU)

Turn the engine switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A9-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
A9-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


Result:
Result Proceed to
OK (for 2AZ-FE) A
OK (for 2GR-FE) B
NG C




A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)