These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1225 | SM Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C1226 | SA2 Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C1227 | SA3 Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C1228 | STR Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C1468 | SFR Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C1469 | SFL Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C146A | SRR Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C146B | SRL Solenoid Circuit | Solenoid valve signal does not match the check result. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
Refer to DTC C146E (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C146E).
These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).
The solenoid circuits are in the skid control ECU (brake actuator assembly).
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and C146B are not output. | A |
| DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and/or C146B are output. | B |
If a speed signal of 20 km/h (12 mph) or more is received by the skid control ECU (brake actuator assembly) with the engine switch on (IG), the skid control ECU (brake actuator assembly) performs self diagnosis of the motor circuit.
If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).
If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B