Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates due to a malfunction in a power supply or charging system circuit such as the battery or alternator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction +BS terminal voltage is more than 16.5 V for 1 second or more.
·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U189562E02
1.208,1.521 1.542,0.781 false 2.75,1.479 2.958,0.729 false 0.344,2.677 0.677,1.583 false 0.271,0.177 0.469,0.333 0.198,0.156 10 false *a 0.229,0.781 0.521,0.938 0.292,0.156 10 false A35 1.469,0.583 1.76,0.74 0.292,0.156 10 false IG1 0.177,2.698 0.469,2.854 0.292,0.156 10 false +BS 2.729,0.552 3.156,0.708 0.427,0.156 10 false GND1

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-25 (+BS) - Body ground Always 11 to 14 V
A35-25 (+BS) - A35-38 (GND1) Always 11 to 14 V
A35-28 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
A35-28 (IG1) - A35-38 (GND1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A35 skid control ECU (brake actuator assembly) connector.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1417 is not output. A
DTC C1417 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B