Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR(for 2GR-FE)
RM24M0E _58 Vehicle Interior _059584 AIR CONDITIONING _0292185 COMPRESSOR(for 2GR-FE) A

AIR CONDITIONING  COMPRESSOR(for 2GR-FE)  INSTALLATION  


PROCEDURE

Hide 88310D 1.INSTALL COMPRESSOR AND MAGNETIC CLUTCH

a.

Install the compressor and magnetic clutch with the 4 bolts.

E147792E04
0.042,0.052 1.583,0.365 1.542,0.313 12 true except Middle east: 3.698,0.021 4.646,0.24 0.948,0.219 12 false Middle east: 0.823,1.135 1.073,1.313 0.25,0.177 10 true (1) 2.354,1.104 2.604,1.281 0.25,0.177 10 true (3) 1.24,1.552 1.49,1.729 0.25,0.177 10 false (4) 1.677,1.594 1.927,1.771 0.25,0.177 10 false (2) 4.427,0.365 4.677,0.542 0.25,0.177 10 false (1) 4.896,0.052 5.104,0.25 0.208,0.198 10 true (3) 4.385,1.25 4.635,1.427 0.25,0.177 10 false (4) 4.823,1.583 5.073,1.76 0.25,0.177 10 false (2)

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the compressor and magnetic clutch.



Hide 88712 2.INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE

a.

Remove the attached vinyl tape from the hose.

E147791E02
0.073,0.042 1.583,0.313 1.51,0.271 12 true except Middle east: 3.854,0.031 4.813,0.281 0.958,0.25 12 true Middle east:


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring onto the No. 1 cooler refrigerant suction hose.


d.

Install the No. 1 cooler refrigerant suction hose onto the compressor and magnetic clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 7.2 ft.*lbf)


Hide 88703 3.INSTALL DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the hose.

E147790E02
0.073,0.042 1.635,0.292 1.563,0.25 12 true except Middle east: 4.083,0.031 5.083,0.333 1,0.302 12 true Middle east:


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring onto the discharge hose sub-assembly.


d.

Install the discharge hose onto the compressor and magnetic clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 7.2 ft.*lbf)


e.

Connect the connector.

E359773E01
0.156,0.042 1.698,0.292 1.542,0.25 12 true except Middle east: 4.042,0.042 5.01,0.354 0.969,0.313 12 true Middle east: 0.49,1.479 1.156,1.708 0.667,0.229 10 false Clamp


f.

Engage each clamp.


Hide 16400 5.INSTALL RADIATOR ASSEMBLY WITH FAN SHROUD AND FAN MOTOR

Hide 6.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT